Bedienungsanleitung Korg i3 (Seite 7 von 36) (Englisch)

707347

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Getting Ready to Play

Introduction

Getting Ready to Play

Connecting the AC adapter

Make sure that the power on the i3 is turned off.

Connect the DC plug of the included AC adapter to the DC

12V jack located on the rear panel of the i3.

Be sure to use only the included AC adapter. Using any

other AC adapter may cause malfunctions.

Hook the AC adapter cord onto the cord hook. Do not use

excessive force when pulling the cord off the hook.

Cord hook

AC adapter

(included)

Be careful not to bend the

part of the AC adapter

plug as shown any more

than necessary.

Connect the plug of the AC adapter to an AC outlet.

Be sure to use an AC outlet of the correct voltage for

your adapter.

Using this instrument with

batteries

You can use six AA alkaline or nickel-metal hydride batteries to

power the i3.

Zinc-carbon batteries cannot be used.

Note:

Batteries are not included, so please obtain them sepa-

rately.

Installing the Batteries

Make sure that the power on the i3 is turned off.

Push the tab on the battery compartment cover that is

located on the bottom of the i3 to open the cover.

Note:

When turning the i3

upside down, place it on a

blanket or similar material to

prevent damage to the dis-

play, joystick and other parts.

When inserting the batteries, be sure to observe the

correct polarity (“+” and “–”).

Do not mix new and old

batteries, or batteries of dif-

ferent types. Failing to observe

this guideline might cause the

batteries to leak or burst.

Close the battery cover.

Note:

To make sure the correct battery level is displayed,

conﬁgure the setting on the i3 for the type of battery you are

using (see “Setting the battery type” on page 25).

Replacing the batteries

A battery indicator is shown at the upper right-hand corner of

the display.

Note:

This indicator will not be displayed when the i3 is con-

nected to an AC adapter.

When the indicator is blinking, this means that the batteries are

nearly depleted, so replace the batteries as soon as possible or

connect an AC adapter to power the i3.

Remove depleted batteries immediately. Leaving depleted

batteries in could result in malfunctions caused by battery elec-

trolyte leakage or similar problems. Also, remove the batteries

if you will not be using the i3 for a long time.

Connecting speakers

Connect the OUTPUT L/MONO, R jacks on the rear panel of the

i3 to a powered monitor speaker, stereo or other audio device.

To output monaural sound, use the OUTPUT L/MONO jack only.

INPUT

Powered monitor speaker

(left)

Standard phone plug

cable (monaural)

Powered monitor speaker

(right)

Turn off the i3 and your audio devices before making con-

nections. Leaving the power on when you make connections

may cause damage to other connected devices, or cause a

malfunction.

The speakers may be unintentionally damaged if the

volume is too loud, if you play the i3 right after the speakers

are turned on. For this reason, when connecting the speakers

or turning on the power, make sure that the speaker volume is

turned all the way down. Do the reverse when turning off the

power.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Korg i3 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Korg i3

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info