Bedienungsanleitung Korg Kross 2 (Seite 74 von 152) (Englisch)

707348

Zoom out

Zoom in

Vorherige Seite

1/152

Nächste Seite

Using Effects

input settings of the KROSS in G-SET (Use Global

Settings), or use the individual parameters of each mode to

specify the BUS or Send settings. (see “Effect settings for

audio input” on page 71)

Depending on the type of effects that you’re using on

the external audio input, and on their settings, it is

possible for feedback to occur. If this occurs, adjust the

input/output levels and the effect settings. Take special

care when using high-gain effects.

Audio recorder

The audio recorder can record the sound as it is processed by

the effects specified in Program, Combination, or Sequencer

mode.

You can’t apply effects to the playback of the audio

recorder.

Pad Sampler, USB Audio

Effects cannot be applied to the playback of the pad

sampler, nor to the USB audio input.

Routing and effect settings

Routing lets you specify how each sound will be connected

to the various effects. In each mode, you can adjust settings

for the program’s oscillators, the combination’s timbres, and

the song’s tracks.

Here we’ll explain how to adjust routing settings in each

mode, and how to edit the effect settings.

Effect settings for a program

Routing

1. Access the P-FX ROUTING> BUS page.

2. “Bus (Bus Select)” specifies the bus where the output

from the oscillators will be sent. Here we’ll choose

IFX1 so that the output of the oscillators will be sent

to insert effect 1.

L/R: The oscillator output will not be sent to an insert

effect. It will pass through the total effect, and then be

sent to OUTPUT L/MONO and R.

IFX1–IFX5: The oscillator output will be sent to insert

effect 1–5.

Off: The oscillator output will not be sent to OUTPUT L/

MONO or R, or to insert effects 1–5. Choose this if you

want to send the sound directly to the master effects at the

send levels specified by Send1 (to MFX1) or Send2 (to

MFX2) (P-FX ROUTING> SEND page).

3. If you selected L/R or Off in step 2, you can use each

oscillator’s Send1 (to MFX1) and Send2 (to MFX2)

parameters to set the send levels to the master effects.

Adjust these settings in the P-FX ROUTING> SEND

page.

If Bus (Bus Select) is set to IFX1–5, the send levels from

the output of each insert effect to the master effects are

specified by the S1 (Send1) and S2 (Send2) parameters

(P-Fx Routing Mixer page). (see step 6 of the next

section, “Insert effects”)

4. “FX Control Bus” sends the output of oscillators 1

and 2 to the FX control bus.

Use this when you want to use a different sound to

control the sound that’s being input to an effect. You can

use two FX control buses to freely control the sound. (see

“FX Control Bus” on page 211 of the Parameter Guide)

Oscillator1 Filter1 Amplier1

Oscillator2

Audio Recorder

Filter2 Amplier2

Return

OUTPUT

L/MONO, R

Send

REC

PLAY

Mic In (mono)

Line In (stereo)

Insert

Eect 1–5

Master

Eect 1, 2

USB Audio

Input

Output

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Korg Kross 2 Seite 74

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Korg Kross 2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info