Bedienungsanleitung Korg Kross 2 (Seite 140 von 152) (Englisch)

707348

140

Zoom out

Zoom in

Vorherige Seite

1/152

Nächste Seite

Appendices

134

Audio input

Can’t input audio

□ Is the input source connected to the MIC IN jack or the

LINE IN jack? → p.21

□ In REALTIME CONTROLS, is the AUDIO IN 1 setting

AUDIO IN turned on? → p.15

□ Is the Line or Mic input selection correct?

• Line and Mic cannot both be input simultaneously. In the

AUDIO IN - QUICK SETTING dialog box, use the

Select setting to choose either Line or Mic. → p.22

□ Are the audio input parameters such as Level, Gain, Play/

Mute, and Bus set appropriately?

• In the AUDIO IN - QUICK SETTING dialog box, select

Line or Mic and check the parameter settings. → p.22

The principal parameters have the following default

values.

Level: 127

Play/Mute: Play

Gain: 00 (Line), 37 (Gain)

Bus: L/R

Too much noise or distortion in the audio input or in the

recorded sound

□ Is the Gain set correctly?

• In the AUDIO IN - QUICK SETTING dialog box, if the

[LINE] or [MIC] indication in the middle of the level

meter is highlighted, the Gain setting is too high, and an

overload is occurring in the input stage. Lower the Gain

value until this indication is not highlighted. → p.22

• Conversely if the Gain setting is too low, the meter will

not move very much. Adjust the Gain value upward.

→ p.22

Programs and Combinations

Settings for oscillator 2 are not displayed

□ Make sure that the OSC (Oscillator Mode) (P-BASIC>

BASIC) parameter is set to Double or Double Drums.

→ p.36

Program does not sound

□ Could the oscillator or amp level be lowered?

→ p.32, 37, 43

□ Could the program be muted?

• Switch the Sound in the PROG> MIXER page for a

program, or in the COMBI> MIXER page for a

combination.

A combination does not play correctly after you load data

□ Are the bank/numbers of the programs used by the

combination the same as when the combination was

created?

Can’t write a Program

□ Is the Memory Protect Program or Combination

checkbox (GLOBAL> SYSTM) cleared? → p.116

□ Banks A–F and bank UA...UD have restrictions on the

categories and banks that allow saving. → p.121

A program selected for a timbre in a combination sounds

different than when played in Program mode

□ When you select a program for a timbre in Combination

mode, the arpeggiator and effect settings from Program

mode are not automatically applied.

• You can use the Copy From Program, Copy Insert

Effect, or Copy Master Effect functions to copy these

settings from Program mode. → PG p.95, 96, 96

Sequencer

A program selected for a track sounds different than when

played in Program mode

□ When you select a program for a track in Sequencer

mode, the arpeggiator and effect settings from Program

mode are not automatically applied.

• You can use the Copy From Program, Copy Insert

Effect, or Copy Master Effect functions to copy these

settings from Program mode. → PG p.139, 151, 151

Song does not play correctly after being loaded

□ Are the programs used by the song the same as when the

song was created?

• When saving the song, it is best to use Save All

(PCG&SNG) so that the programs are saved together

with the song. Then when loading, load both the .PCG

and the .SEQ data. → p.127

Playback does not start when you press the SEQUENCER

(start/stop) button in Sequencer mode

□ Is the MIDI Clock (G-MIDI> BASIC) set to Internal or

Auto? → p.117

Can’t record in Sequencer mode

□ Did you use Track Select to select the MIDI track that

you want to record? → p.61

□ Is the Memory Protect Song check box (GLOBAL>

SYSTM) unchecked? → p.116

□ Is the MIDI Clock (G-MIDI> BASIC) set to Internal or

Auto? → p.117

A combination copied using “Copy From Combination”

doesn’t record via arpeggiator as it did when you were

playing it in Combination mode

□ Is Multi REC (SEQ> MAIN) checked? → p.61 and

PG p.108

□ Are the settings in the Copy from Combination dialog

box correct? → PG p.138

• In the Copy from Combination dialog box, check the

Auto adjust Arp setting for Multi REC option before

you execute the copy. This will cause the settings to be

adjusted automatically.

Can’t record Tone Adjust data

□ Changes you make using Tone Adjust are recorded as

system exclusive data. Did you check the G-MIDI>

FILTER Enable Exclusive check box? → PG p.163

SMF you loaded in Media mode won’t play correctly

□ Execute the GM Initialize function to restore the

settings. → PG p.141

□ Set Bank Map to GM(2) and load the data again.

→ PG p.158

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Korg Kross 2 Seite 140

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Korg Kross 2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info