Bedienungsanleitung Korg microKORG XL (Seite 7 von 103) (Englisch)

707337

Zoom out

Zoom in

Vorherige Seite

1/103

Nächste Seite

Introduction

8. [VOCODER] (AUDIO IN THRU) button

This turns the vocoder on/off (J p. 13). (When on, the LED above the but-

ton will be lit.)

By holding down the [EXIT/SHIFT] button and pressing this button, you can

switch the AUDIO IN THRU setting (J p. 13).

9. [WRITE] button

Press this button to save a program or global settings you’ve edited

(J p. 31).

10. [EXIT/SHIFT] button

Press this button to stop a Save or Utility operation.

By pressing this button in conjunction with another button, you can play a

demo or switch the AUDIO IN THRU setting.

11. [TIMBRE SELECT] lever

Use this to select the timbre that you want to edit (J p. 22).

The selected timbre is indicated by the lit LED beside this lever.

NOTE

If the COMMON page setting “VOIC.MODE” is “SINGLE,” the [TIMBRE

SELECT] lever does nothing.

12. [KNOB FUNCTION SELECT] dial

This dial selects the function of knobs [1], [2], and [3].

If the dial is set to ASSIGN, FILTER, AMP EG, or ARP, the timbre selected

by the [TIMBRE SELECT] lever will be the target of your editing, and you’ll

be able to use the performance edit functions (J p. 22).

If the dial is set to EFFECT, performance editing will control the dry/wet bal-

ance for FX1 and FX2 and the parameter that’s assigned to Control 1 of

FX1.

If the dial is set to FULL EDIT, the knobs will operate in full edit mode,

allowing you to select a page and parameter, and to edit the value of that

parameter (J p. 23).

13. [1], [2], [3] knobs

Use these knobs for performance editing and in full edit mode to select the

page, parameter, and parameter value.

14. ORIGINAL VALUE LED

This LED will light when the value of the parameter you’re editing matches

the value stored in the program.

15. Display

Information on the selected program is shown here. In full edit mode, the

display shows the selected page, the current value of the parameter, vari-

ous messages, or other information.

a: Battery empty indicator

b: Edit indicator

c: This will appear when the position of the [PROGRAM GENRE] dial,

[PROGRAM CATEGORY] dial, or [BANK SELECT] lever no longer

matches the actual program number, such as when a MIDI program

change message has been received.

d: Global indicator

e: When “KNOB MODE” is CATCH, this indicates the direction of the actual

value relative to the knob position.

f: Level meter

g, h: These areas display program information, or indicate the parameter or

parameter.

i: Cursor

16. [PITCH] wheel

This controls the pitch.

17. [MOD] wheel

This controls the depth of modulation.

18. AUDIO IN [MIC] (XLR) jack

You can connect a mic here.

If you want to use a mic connected to this jack, set the rear panel [XLR/

LINE] switch to the “XLR” position. Use the rear panel AUDIO IN [LEVEL]

knob to adjust the level.

ab cde

Introduction

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Korg microKORG XL Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info