Bedienungsanleitung Korg microKORG XL (Seite 82 von 103) (Englisch)

707337

Zoom out

Zoom in

Vorherige Seite

1/103

Nächste Seite

microKORG XL

• Normally when controlling the microKORG XL’s tone generator from an

external MIDI device, you will set “POSITION” to PRE TG. The various set

tings listed above will affect the MIDI data that is received.

The transmitted data will be processed as “TRANSPOS”: 0 and

“VEL.CURVE”: 4.

“MIDI FILTER” settings

The MIDI FLT page setting specifies whether program change, pitch bend,

control change, and system exclusive messages will be transmitted or

received. (J p. 60)

Virtual patch modulation source settings

You can assign three different MIDI control messages (MIDI 1, 2, 3) as vir-

tual patch modulation sources. Make the desired assignments in the

PATCH page (J p. 61), and then select MIDI1 or MIDI2 etc. as the virtual

patch source for the virtual patch settings (PATCH1–PATCH6). This lets

you control modulation via MIDI.

The modulation source “FC.MOD.SRC”of the cutoff frequency of the

vocoder’s carrier band-pass filters can also be controlled via MIDI; simply

select MIDI 1, 2, or 3 as the virtual patch modulation source.

“CONTROL CHANGE” settings

You can assign control change numbers to the major parameters that affect

the sound, and use an external MIDI device to perform the same operations

as when the knobs and keys of the microKORG XL are operated. Con-

versely, you can operate the microKORG XL’s knobs and keys to control

an external MIDI device. Use the CC MAP page to assign control change

messages to parameters. (J p. 61)

MIDI “LOCAL” setting when connecting an external MIDI sequencer or

computer

If notes are sounding doubled when the microKORG XL is connected to an

external MIDI sequencer or computer, turn the Local setting off (MIDI page

“LOCAL” OFF). (J p. 59)

If the microKORG XL is connected to an external MIDI sequencer or com-

puter, and the Echo Back setting of the external MIDI sequencer or com-

puter is turned on while the microKORG XL’s Local Control setting is also

on, the performance data generated when you play the microKORG XL’s

keyboard will be sent to the external MIDI sequencer, and will also be

echoed-back to sound the microKORG XL’s tone generator a second time.

To prevent each note from being sounded twice, once directly from the key-

board and once from the echoed-back note, you must turn the microKORG

XL’s Local Control setting off.

Recording the MIDI output from the microKORG XL’s arpeggiator onto

an external MIDI sequencer or computer

Connect and setting

Connect the microKORG XL’s MIDI OUT connector to the MIDI IN connec-

tor of your external MIDI sequencer / computer, and connect the

microKORG XL’s MIDI IN connector to the MIDI OUT connector of your

external MIDI sequencer / computer. Then turn the microKORG XL’s Local

Control off (MIDI page “LOCAL” OFF), and turn on the echo back setting of

your external MIDI sequencer / computer.

Recording the note data from the arpeggiator onto an external

MIDI sequencer / computer

Set the microKORG XL’s GLOBAL page “POSITION” to POST KBD

Turn on the microKORG XL’s arpeggiator (ARPEGGIATOR [ARP ON] but-

ton lit), play the keyboard, and record the note data on your external MIDI

sequencer / computer. If the GLOBAL page “POSITION” is set to POST

KBD, the MIDI note data produced by the arpeggiator will be output from

the microKORG XL, and recorded. Turn the microKORG XL’s arpeggiator

off during playback.

Synchronizing the arpeggiator

The MIDI page “CLOCK” setting specifies whether the microKORG XL’s

arpeggiator will be the master (the controlling device) or slave (the con-

trolled device).

NOTE

For information on synchronization-related settings of your external MIDI

device, refer to the manual of your device.

Using the microKORG XL as master and the external MIDI device

as slave

Connect the microKORG XL’s MIDI OUT connector to your external MIDI

device’s MIDI IN connector.

Use knob [1] to select the MIDI page, use knob [2] to select “CLOCK,” and

use knob [3] to select “INTERNAL”; the microKORG XL will be the master,

and will transmit MIDI timing clock messages.

Set your external MIDI device to receive incoming MIDI clock messages.

The external MIDI device (e.g., sequencer or rhythm machine) will operate

at the tempo specified by the microKORG XL’s [TEMPO] knob.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Korg microKORG XL Seite 82

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info