707337
85
Zoom out
Zoom in
Vorherige Seite
1/103
Nächste Seite
MIDI
85
•Expression (CC#11) [Bn, 0B, vv]
When expression messages are received, the volume of a timbre will be
controlled. The volume will be at maximum if the maximum value (127) is
received, and at zero if the minimum value (0) is received.
Damper pedal (CC#64) [Bn, 40, vv]
Incoming damper pedal messages will turn the timbre’s damper effect
(Hold) on/off (0: Off, 127: On).
Portamento (CC#65) [Bn, 41, vv]
When portamento messages are received, the portamento effect of a tim-
bre will be switched on/off. If the portamento time is set to 0, there will be no
portamento effect. (0: off, 7F: on)
All note off (CC#123) [Bn, 7B, 00] (value is 00)
When an All Note Off message is received, all currently-sounding notes of
that channel will be turned off. Some sound may linger due to the envelope
settings.
All sound off (CC#120) [Bn, 78, 00] (value is 00)
When an All Sound Off message is received, all notes currently sounding
on that channel will be silenced. While All Note Off allows the decay of a
note to continue, the All Sound Off will silence the sound immediately. How-
ever, this message is intended for use in emergencies, and is not for use
during a performance.
Reset all controllers (CC#121) [Bn, 79, 00] (value is 00)
When a Reset All Controllers message is received, all controller values cur-
rently operating on that channel will be reset. Some parameters assigned
using Virtual Patch will not be reset.
Using a control change as a virtual patch modulation source
By selecting CC#cc (cc=00–95, 102–119) as the “SOURCE” for MIDI1,
MIDI2, or MIDI3 in the PATCH page, you can use control changes as a
modulation source for a virtual patch, vocoder “FC.MOD.SRC,” or effect
parameter. The actual value of 0–127 will be used without change as the
modulation source.
Assigning a control change to a knob or button
In the CC MAP page, you can assign the control changes CC#00–CC#95
and CC#102–CC119 to principal parameters that correspond to panel
knobs and buttons. When you operate an assigned knob or key, the corre-
sponding control change will be transmitted. When that control change is
received from an external device, the result will be the same as if that knob
or key had been operated with the corresponding value. (J p. 90 “4.Front
panel knob/button control change assignments”)
MIDI
85

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Korg microKORG XL wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info