Bedienungsanleitung Korg PS60 (Seite 7 von 68) (Englisch)

668723

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

Front and rear panels Front panel

When you press one of these buttons, the display will

alternate between showing performance-related

information and timbre-related information.

Note: If you’re making single or layer settings, make

sure that the indicators are lit for all of the timbres that

are turned on. When making split settings, you can

press the LOWER or UPPER button to see the indica-

tors of the timbres that are turned on for the lower and

upper regions specified by the SPLIT SETTING but-

tons.

Variation the  buttons

Use these buttons to select variations (programs) for

each timbre.

5. SPLIT SETTING

Here you can divide the PS60’s keyboard into lower

and upper regions and specify timbres separately for

each region. Such setups are called “splits” (p. 14).

LOWER and UPPER buttons

Use these buttons to specify the timbres for the lower

or upper region, or to check the timbres that are split.

If you press one of these buttons when (non-split)

single or layer settings are active, the Timbre On

button will blink, and you’ll be able to select the timbre

used by the button you pressed (LOWER or UPPER).

You can press the EXIT button to exit this state. If split

settings are active, pressing one of these buttons lets

you see which timbres are used by the lower or upper

region; the Timbre On button of the corresponding

timbres will light.

How to specify the split point: Press the LOWER

button and UPPER button simultaneously. Then press

the key that you want to specify as the split point; that

key will be the new split point. If you decide not to

make the setting, press either of these buttons or the

EXIT button.

SUB OFF/RECALL button

This button temporarily cancels the split setting so that

only the main timbre (p. 7) will be played by the full

range of the keyboard. If you press this button to

cancel the split setting, the button indicator will light.

The sub timbre settings are remembered while this

button is lit.

Audition function: If you press the SUB OFF/RECALL

button and the LOWER button simultaneously, a riff

(phrase) specified for each timbre program will play

repeatedly. This function will turn off when you press

either button or the EXIT button. You won’t be able to

turn this function on if layer or split settings are active

(p. 16).

6. MODULATION

Here you can add rich spaciousness, modulation, or

movement to the sound (p. 20).

MODULATION TYPE button

Use this button to select the effect type. Each press of

the button will cycle through the effect types (the

corresponding indicator will light).

CHORUS: Stereo chorus that adds richness and

warmth to the sound

FLANGER: Stereo flanger that applies dramatic

modulation and a sense of pitch change to the sound

VINTAGE CHO/FLG: Vintage analog chorus/flanger

that produces the warm and rich sound typical of an

analog effect processor

PHASER: Stereo phaser that produces modulation by

shifting the phase of the sound

EFFECT OFF: (no indicators lit)

6 7 8

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Korg PS60 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info