Bedienungsanleitung Korg PS60 (Seite 61 von 68) (Englisch)

668723

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

Troubleshooting Audio output

 The same program might sound different because

of differences in the performance’s tone parameters,

timbre parameters, master effects, and EQ settings.

 Return the edited parameter to its original value, or

change parameters of differing values to the same

value.

 If a timbre’s tone parameters (p. 31) have been

edited (this can happen by receiving certain CC#s),

you can return to the saved settings by reselecting

the program.

 If timbre parameters have been edited (this can

happen by receiving certain CC#s), you can return

to the saved settings by reselecting the performance.

Alternatively, you can execute Initialize

Performance to initialize the parameters of the

performance. After doing either of the above steps,

reselect the performance.

* The timbre parameters include Volume, Pan (Pre),

Pan (Post), OSC Select, OSC Mode, Portamento,

Octave, Transpose, Detune, and UsePrgScl.

In Performance Edit, can’t change the value

of a timbre parameter such as “MIDI

Channel” or “Status”

 Some parameters can’t be edited while notes are

playing, either locally or from MIDI. If the damper

pedal is held down, or if its calibration is incorrect,

notes may be sustaining even if they aren’t audible.

 Are you using a damper pedal with a polarity that

does not match the “Polarity (Switch Polarity)”

setting? p. 52

 In some cases, this problem can be solved be

executing the command “HalfDmpr Calib (Half

Damper Calibration)”. p. 53

Effects and EQ

Effects or EQ are not applied

 Could the Effect SW “ALL IFXs,” “MFX1&2,” or

“EQ” be Off? p. 49

 Could No Effect be selected as the effect type?

 On the front panel, press the MODULATION

button or REVERB/DELAY button to select an

effect. p. 20

 In the edit page, select something other than No

Effect for “IFX,” “MFX1(Mod),” and “MFX2(Rev).”

p. 30, 44

 Could the Effect SW settings “All IFXs,” “MFX1&2”

or “EQ” be Off? p. 49

 In a performance, if the master effect still does not

apply even when you’ve raised the timbre’s

“Send1(Mod)” and “Send2(Rev)” settings, are the

“Return1” and “Return2” settings from the master

effect raised? p. 49

Could the “Send1(Mod)” or “Send2(Rev)” settings

for each program oscillator used by the timbre be

lowered? p. 30

Note: The actual send level is determined by

multiplying the send of each of the program’s

oscillators by the send setting of the timbre track.

Insert effect is not applied

 Could you have changed the program’s category

when saving it? p. 46

 The STRINGS timbre does not have an insert effect.

 Could the IFX “On/Off” setting be Off? p. 45

The blinking speed of the ORGAN FAST/

SLOW button does not match the speed of

the rotary speaker simulator

 If you switched the speed of the rotary speaker

simulator by operating the joystick in the +Y

direction, the ORGAN SLOW/FAST button’s

blinking speed will not change. Press the ORGAN

SLOW/FAST button to change the blinking speed.

Alternatively, operate the joystick once again in the

+Y direction to switch the rotary speaker simulator’s

speed.

The ORGAN SLOW/FAST button does not

blink

 The ORGAN SLOW/FAST button blinks only for

ORGAN programs in which 63 Rotary SP is selected

as the insert effect.

MIDI

The PS60 does not respond to incoming MIDI

data

 Are all MIDI cables or USB cables connected

correctly? p. 12, “PS60 USB-MIDI Setup Guide”

 Is the MIDI data being received on the channel on

which it is being transmitted? p. 50, 30

The PS60 does not respond correctly to

incoming MIDI data

 Are the MIDI Filter settings “Prog Chg,” “Bank

Chg,” “AfterTouch,” “Ctrl Chg,” and “SysEx”

respectively turned On? p. 51, 32

 Does the PS60 support the types of messages that

are being sent to it? p. 63

Incorrect response to program change

messages

 Is the “Bank Map” setting correct?  PG p.134

 Program changes on the global MIDI channel

correspond to performances.

 The programs of the timbres will not switch.

Pedal does not respond correctly

Damper response is wrong

 Execute the “HalfDamper Calib” command (Global

- Command) to correctly adjust the sensitivity of the

half damper pedal. p. 53

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Korg PS60 Seite 61

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info