668722
87
Zoom out
Zoom in
Vorherige Seite
1/99
Nächste Seite
Appendices
85
Set the counter display to “FreeTime” and check the
amount of recordable time. (p.56)
Is the bounce setting (“BOUNCE”) appropriate?
(p.29)
If the bounce setting (“BOUNCE”) is set to “CONV,”
the recording will be created as a new song. (p.51)
Can’t record two tracks simultaneously
The “EFFECT ASSIGN” (effect insert location) may
have been set to “GUITAR.”
If this is set to “GUITAR,” only one track can be
recorded simultaneously.
Input sound or recorded sound contains noise or distor-
tion
Is the [TRIM] knob raised to an appropriate level?
If the [TRIM] setting is too high the sound will distort;
if it is too low, noise will be heard. (p.18)
If the effect input is distorted, make the following
adjustments.
Guitar/insert effect: Hold down the [SHIFT] key and
press the [DISPLAY] key, and select the “PRE” setting
for “DISPLAY.” Then use [TRIM] etc. to adjust the
input volume as high as possible without allowing
“CLIP” to light in the level meter.
Master effect: Adjust the faders and send level so that
“CLIP” for the master L/R track does not light.
Final effect: Adjust the faders so that “CLIP” does not
light for the master L/R track.
If the effect output is distorted, make the following
adjustments.
Guitar/insert effect: Adjust the effect parameters and
[TRIM] while listening to the sound.
Master/final effect: Adjust the effect parameters so
that “CLIP” for the master L/R track does not light.
Effect does not apply
Tuner mode may have been selected.
The effect will be bypassed (off) when the tuner is
selected.
Is the master volume of the effect program set to “0”
or close to “0”?
Press the [EFFECT] key, then press the [CURSOR]
right key several times to display “ProgMVol,” and
raise the volume setting.
Is the [TRIM] knob raised to an appropriate level?
If the [TRIM] setting is too low, the effect may not be
applied in some cases.
Guitar/insert effect does not apply
Is the effect insert location appropriate?
Hold down the [SHIFT] key and press the [EFFECT]
key, and set “EFFECT ASSIGN” to “GUITAR” or
“INSERT.” (p.35)
It is not possible to use a guitar/insert effect on a play-
back track.
Master effect does not apply
Is the effect insert location correct?
Hold down the [SHIFT] key and press the [EFFECT]
key, and set “EFFECT ASSIGN” to “MASTER.”
(p.35)
Is the send level from each track set to “0”or close to
“0”?
Press the [MIXER] key, and use the [CURSOR] keys to
raise the “Send-L” and “Send-R” send levels.
87

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Korg PXR4 Pandora wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info