Bedienungsanleitung Korg R3 (Seite 25 von 94) (Englisch)

668721

Zoom out

Zoom in

Vorherige Seite

1/94

Nächste Seite

Editing

Basic editing procedures

On the R3 there are two basic ways for you to create your own sound(s).

• Select a program that is close to the sound you want to create, and tweak

the parameters of that program until it sounds the way you would like

it to.

• Start from an initialized program (“blank slate”), and create the sound

from scratch

All of editable parameters are organized into sections, and the param-

eters in each section are accessed by selecting different edit pages. When

creating a sound from scratch, notice that the edit pages are organized in

a way that follow the logical order of editing. You can turn the dial to

step through these sections in the appropriate order. Broadly speaking,

the procedure is as follows.

Select the program that you want to start from. (☞p.12)

If you want to start from scratch, execute the Initialize operation. (☞p.75)

Use the TIMBRE SELECT [TIMBRE1], [TIMBRE2], or [VOCODER]

buttons to select the part that you want to edit.

Turn the [PAGE] dial to select the edit page that includes the parameter

you want to edit. Consider how the current program differs from the sound

you have in mind, and select the parameter that you want to edit.

3 Edit the value of the parameters available in the selected page, using

knobs [1], [2], [3], and [4]. The parameter controlled by each knob is

shown in the sub-display located above each knob.

For example if you’re editing a synth program, and you’ve selected the

8. Filt-A page in step 2, knob [1] will adjust the cutoff frequency, knob

[2] will adjust the resonance, knob [3] will adjust the filter balance, and

knob [4] controls the filter routing.

Go ahead and try editing the 15. EG2 page ozBameters “Attack2” and

“Decay2” (☞p.41), the 3. Pitch-A page parameter “Portamnt” (☞p.25),

or the 29. Insert FX1 page parameter “Type” to hear the result (☞p.49).

Repeat steps 2–3 as necessary to create the desired sound.

Write the program into memory. (☞p.74)

If you select another program or turn the power off before you write

the program into memory, your edits will be lost.

The difference between Catch and Jump modes

In some cases, the parameter values won’t seem to change when you

are turning knobs [1]–[4]. This can happen if the “KnobMode” (41.

Global-B page) is set to Catch. In the Catch mode, the physical knob

must be turned to the position matching the stored value (shown by

the LEDs around the perimeter of each knob) before any further

editing of that parameter can begin. This allows you to make fine

adjustments without any sudden or unnatural-sounding “jumps”

occurring in the sound.

For example, suppose that before you begin editing, the knob

is in the position shown at left.

The actual value of this parameter is saved at the position

shown by the triangle in the diagram at left. In the Catch

mode, the parameter value will not change until you turn the

knob all the way to that position.

Once the knob reaches the position of the actual saved value, the

knob and parameter value will begin changing in tandem, and you

can begin to edit the value.

On the other hand, if the “KnobMode” is set to Jump, turning the

knob will cause the parameter’s value to jump immediately to the

actual position of the knob.

Basic editing

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Korg R3 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info