Bedienungsanleitung Korg SoundLink DRS 1212 I-O (Seite 14 von 58) (Englisch)

488479

Zoom out

Zoom in

Vorherige Seite

1/58

Nächste Seite

Installation

10 Korg 1212 I/O

English

one end, which connects to the 1212 I/O, and fans out to a pair of female

RCA connectors. One of these connectors is white, and labeled “In,” while

the other is yellow, and labeled “Out.”

S/PDIF stands for “Sony/Philips Digital Interface.” The S/PDIF format

carries two channels of digital audio, and is commonly used for

transferring stereo signals between DAT recorders, digital signal

processors, digital musical instruments, and so on.

S/PDIF input.

The white RCA connector, labeled “In,” is the S/PDIF input.

You can connect this to the S/PDIF output of a DAT, signal processor,

sampler, and so on. Please use high-quality, shielded, 75-ohm cables

manufactured speciﬁcally for video or digital audio.

The 1212 I/O can accept either 16 or 20 bit audio data via the S/PDIF input.

S/PDIF output.

The yellow RCA connector, labeled “Out,” is the S/PDIF

output. You can connect this to the S/PDIF input of a DAT, signal

processor, sampler, and so on. Please use high-quality, shielded, 75-ohm

cables manufactured speciﬁcally for video or digital audio.

The 1212 I/O can transmit either 16 or 20 bit audio data via the S/PDIF

output.

❻

Word Clock and ADAT Sync breakout connector

This connector should only be used with the special Word Clock and ADAT

breakout cable included with the 1212 I/O. This cable has a 6-pin mini-DIN

connector at one end, which connects to the 1212 I/O, and fans out to a pair

of female BNC connectors, one yellow and one white, and the ADAT 9-pin

D-sub sync connector.

ADAT sync input.

This 9-pin connector receives timecode from the ADAT

system. 1212 I/O-compatible digital audio software can use this to

synchronize recording and playback with a connected ADAT system.

Connect this to the ADAT Timecode Conditioner (described below) and

then to the ADAT’s sync out port. If you have multiple ADATs in your

system, connect this to the sync output of the last machine in the chain.

Word Clock input.

The white BNC connector, labeled “In,” is the Word

Clock input. This allows the sample rate of the 1212 I/O to be controlled by

an external device. Connect this to the word clock output of the master

clock source.

The Word Clock input requires a shielded, video-quality cable (75-ohm or

greater impedance) with BNC connectors. This type of cable is different

from those commonly used in analog audio applications, but is readily

available at professional audio and video dealers.

Word Clock output.

The yellow BNC connector, labeled “Out,” is the Word

Clock output. This allows the 1212 I/O to control the sample rate of an

external device; it will always echo the currently selected Clock Source (see

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Korg SoundLink DRS 1212 I-O Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Korg SoundLink DRS 1212 I-O

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info