Bedienungsanleitung Korg X50 (Seite 123 von 132) (Englisch)

668615

123

Zoom out

Zoom in

Vorherige Seite

1/132

Nächste Seite

Troubleshooting

117

Quick StartIntroductionSetupProgram

Combination

MultiEffectGlobalArpeggiatorDrum Kit

External control

Appendices

Troubleshooting

If you experience problems, see the relevant item

and take the appropriate measures.

Power supply

Power does not turn on

Is the AC adapter connected to an outlet?

☞p.23

Is the Power switch turned on?

→ Turn on the rear panel Power switch. ☞p.23

Display

The power is turned on, but nothing is

shown in the display.

The X50 functions normally when you

play the keyboard or perform other oper-

ations.

Due to changes in the surrounding tempera-

ture, the display may on rare occasions be difﬁ-

cult or impossible to read. If this occurs,

perform the following procedure.

1. While holding down the [EXIT/CANCEL]

button, press the [UTILITY] button. The

[GLOBAL] button will blink, and the Global

mode Update Global Setting dialog box will

appear.

If you are unable to read the display, or if the

Update Global Setting dialog box does not

appear, check whether the [GLOBAL] button

is blinking. If the [GLOBAL] button is lit or

dark, the X50 may be writing data that was

received from an external connected MIDI

device, or may be responding to a request for

output. If so, make sure that the X50 is not

writing data from an external connected MIDI

device or transmitting data in response to a

request, or that any such operation has been

completed. Then turn the power of the X50 off

and on again, and repeat this procedure from

step 1.

2. Use the [VALUE] dial to adjust the LCD

contrast.

3. Press the [MENU/OK] button.

The LCD contrast setting will be memorized.

Note: Other global settings will also be memorized

at this time.

The power is turned on, but the display

does not display normally, or an error

message is displayed. There is no sound

when you play the keyboard, and the X50

does not function normally.

This type of problem may occur if a data writ-

ing operation to internal memory was not com-

pleted correctly, for example if the power of the

X50 was turned off while a program or other

data was being written. If this occurs, use the

following procedure to initialize the X50’s

internal memory.

1. Turn off the power.

2. Hold down the [ENTER] button and the [0]

button, and turn on the power.

The X50 will be initialized, and the factory

preload data will be written into internal

memory. While the data is being written, the

display will indicate “Now writing into

internal memory.”

Audio output

No sound

Are connections made correctly to your amp,

mixer, or headphones?

Is your amp or mixer turned on?

Is Local Control turned on?

In GLOBAL 1: MIDI, check the “Local Control

On” check box. ☞PG p.82

Is the [VOLUME] slider raised? ☞p.12

If there is no sound from the INDIVIDUAL

OUTPUT 1, 2 jacks, make sure that “BUS

Select” or “BUS Select” following the insert

effect is set to 1, 2, 1/2. ☞p.81

If speciﬁc tracks in Multi mode do not

sound, Make sure that the “PLAY/MUTE” is

set to PLAY. ☞p.70

Make sure that the “Status” is INT or BTH.

☞p.71

Are the “Key Zone” and “Velocity Zone” set so

that sound will be produced when you play?

☞p.65

Notes do not stop

In PROG 1: Ed–Basic, select the Prog Basic

page, make sure that the “Hold” check box is

unchecked. ☞PG p.6

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Korg X50 Seite 123

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info