Bedienungsanleitung Korg Zero 4 (Seite 7 von 93) (Deutsch, Englisch, Französisch)

668583

Zoom out

Zoom in

Vorherige Seite

1/93

Nächste Seite

10. FX ON/MUTE switch

If you move this switch to the FX ON position, the channel effect of

that mixer channel will be enabled, using the wet/dry mix you set

with FX MIX knob (9.). If you return the switch to the center position,

the channel effect will not be applied.

If you hold the switch in the MUTE position, the sound of that mixer

channel will be muted.

TIP: You can’t leave the switch set to the MUTE position.

11. CUE button

When the CUE button is lit (ON), the pre-fader sound of that mixer

channel will be sent to the CUE bus. By setting the MONITOR BAL

knob toward CUE, you can monitor the sound of the CUE bus through

headphones.

12. A, B buttons

By pressing the A or B button you can assign this mixer channel to ei-

ther side of the crossfader (crossfader channel A or B).

13. Channel fader

Adjusts the level of the input audio assigned to this mixer channel.

14. Crossfader

Crossfades the sounds that are assigned to the crossfader’s channel A

and channel B, and outputs the result to the master bus.

15. MIC INPUT jack

This is a combo-type balanced input jack

that allows the use of TRS phone plugs or

XLR plugs (+48V phantom power is sup-

plied).

16. +48V PHANTOM switch

This turns the phantom power supply on/

off for the MIC INPUT jack.

Phantom power is supplied only to the

balanced XLR jack, not to the phone jack.

Note: If you connect or disconnect a condenser mic with the phan-

tom power switch turned on, you risk damaging your equip-

ment. Make sure that the phantom power switch is off before

you connect or disconnect a condenser mic.

Caution

: Never connect any device other than a condenser mic if the

phantom power switch is on. Doing so may damage your

equipment.

17. MIC GAIN switch

This sets the mic preamp gain for the MIC INPUT jack.

18. GUITAR jack

Connect a guitar or bass guitar to this jack.

This is a 1/4" phone-type unbalanced input jack.

19. FireWire indicator

If the ZERO4 is connected to your computer via a FireWire cable, this

indicator will light when the connection is detected.

TIP: Start up your host application after this indicator has lit.

20. CH SELECT switch

This switches the send to the SAMPLER/FX bus. The LED of the se-

lected channel will light, and all sound of the mixer channel will be

sent to the SAMPLER/FX bus. You may select more than one channel

simultaneously.

LED lit: The audio of the mixer channel will be connected to the SAM-

PLER/FX bus. This will be the source audio for the loop sampler and

master effect.

LED dark: The audio of the mixer channel will not be sent to the SAM-

PLER/FX bus.

21. LOOP LENGTH knob

This specifies the recording/playback time of the loop sampler.

22. KEEP button

This indicates the sample hold status of the loop sampler. If a sample

is already being held, pressing the KEEP button will erase the sample.

LED lit: A sample is being held.

LED dark: No sample is being held.

23. LOOP PLAY button

This records/plays the loop sampler. If no sample is being held, this

button will initiate recording. If a sample is being held, this button will

initiate loop playback.

2: HOT

1: GND

3: COLD

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Korg Zero 4 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info