Bedienungsanleitung Korg Zero 4 (Seite 16 von 93) (Deutsch, Englisch, Französisch)

668583

Zoom out

Zoom in

Vorherige Seite

1/93

Nächste Seite

will be heard during the interval specified

by the TIME knob.

FB: Adjusts the amount of change to the shape

of the LFO waveform.

PITCH SHIFT Shifts the pitch of the input audio upward

or downward.

TIME : Adjusts the delay time.

MOD: Adjusts the pitch of the input audio.

FB: Adjusts the amount of feedback for the

pitch-shifted sound.

DELAY A stereo delay.

TIME: Adjusts the delay time.

MOD: Adjusts the time before reaching the delay

time specified by TIME.

FB: Adjusts the amount of feedback.

TAPE ECHO An effect that simulates a tape echo.

TIME: Adjusts the delay time.

MOD: Adjusts the output level.

FB: Adjusts the amount of feedback.

The display indication when operating the TIME knob

When you operate the TIME knob, the specified TIME parameter is shown

in the display for approximately two seconds. The number shown indi-

cates the beat. For example, a beat of 1/4 (quarter note) is shown as “1.4”

in the display.

Limitations on the delay time

Depending on the combination of the BPM synchronization setting and the

TIME parameter, the TIME parameter of the channel effect may exceed the

allowable range. If this occurs, the display will indicate “FULL,” and the

delay time will be set to the maximum allowable setting.

6. Loop Sampler and Master Effect

The loop sampler and the master effect are connected to the SAMPLER/FX

bus in series.

Input channel selection and mixing

The audio of the mixer channel selected by the CH SELECT switch is sent

to the SAMPLER/FX bus, and will be the input signal for the loop sampler

and master effect.

The MASTER FX & SAMPLE MIX fader will adjust the mix balance be-

tween the sound that has passed through the loop sampler and master

effect, and the sound (“dry” sound) selected by the CH SELECT switch. By

pressing the CUE button, you can monitor the “wet” sound via the CUE

bus even if this is set to the “dry” side.

Loop sampler

This is a loop sampler that lets you play the recorded sample using either

Gate Play or Loop Play methods.

Operating procedure

1. Specify the recording/playback time.

The recording/playback time is specified by the LOOP LENGTH

knob, relative to the BPM.

Use the LOOP LENGTH knob to specify the number of beats that will

be recorded/played-back. For example if you set the LOOP LENGTH

knob to “1/4”, the length will be one quarter-note beat. The duration

of one beat depends on the BPM value. (Refer to the table. Units are

seconds.)

BPM 120 40 60 200 300

1/256 0.008 0.023 0.015 0.005 0.003

1/32 0.625 0.186 0.125 0.375 0.025

1/8 0.25 0.75 0.5 0.15 0.1

1/4 0.5 1.5 1 0.3 0.2

1/1 2641.2 0.8

4/1 824164.8 3.2

2. Using Gate Play and Loop Play.

To sample with Gate Play

When you press the GATE PLAY button, sampling will occur only for

the time specified by the LOOP LENGTH knob.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Korg Zero 4 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info