Bedienungsanleitung Korg Zero 4 (Seite 19 von 93) (Deutsch, Englisch, Französisch)

668583

Zoom out

Zoom in

Vorherige Seite

1/93

Nächste Seite

FireWire interface functions

You can connect the ZERO4 to your computer via a FireWire cable and use

it as an audio/MIDI interface.

Note: This device does not supply bus power.

Note: Do not simultaneously connect more than one computer to

the ZERO4.

Note: If you are using a host application such as sequencing soft-

ware, you’ll need to make audio and MIDI device settings.

For details, refer to the owner’s manual of the software you’re

using.

Note: You must connect the ZERO4 to your computer using a

FireWire cable and turn on the power before you start up your

software. Don't disconnect the FireWire cable or power-off

the ZERO4 while the software is running.

Note: If you're using the ZERO4 with Mac OS X, turn off the Sleep

setting and power management settings.

Note: Each input/output device can be used with only one software

application. Multi-client operation is not supported.

Note: Use the included CD-ROM to install the "KORG FireWire

Audio/MIDI driver" into the computer you're using. (☞

p.23)

1. FireWire audio interface

You can use the ZERO4 as an audio interface. This lets you send the

ZERO4’s audio inputs or mixed sound to your computer, and send the

audio outputs from a host application on your computer to the ZERO4.

Your FireWire-connected computer will detect the ZERO4 as an audio in-

terface that provides a maximum of 8-in and 16-out audio streams.

Limitations for different sampling rates

If the ZERO4 is connected to your computer, you’ll be able to change the

sampling rate from the control panel of the host application or audio

driver.

The available number of effects and mixer channels will depend on the

sampling rate you select.

44.1 kHz or 48 kHz operation: Four stereo channels + channel effects,

loop sampler, master effect

96 kHz operation: Four stereo channels

Note: When operating at 96 kHz, the channel effects, loop sampler,

and master effect are not available.

Note: When using the ZERO4 with Mac OS X

Depending on the system you're using, you may experience

problems such as the operating system becoming unstable

when you switch the sampling frequency.

If this occurs, you can start up as described below so that the

ZERO4 will operate with a fixed sampling frequency. In this

case, you won't be able to switch to another sampling fre-

quency from the computer.

44.1 kHz: Turn on the power while holding down the mixer

channel 1 Cue button.

48 kHz: Turn on the power while holding down the mixer

channel 2 Cue button.

96 kHz: Turn on the power while holding down the mixer

channel 3 Cue button.

In the Mac OS System Settings / Sound / Output dialog box,

verify that the ZERO4 has disappeared from the list of sound

output devices, and then turn the power on once again.

Depending on the type of computer you're using, starting up

the computer with the ZERO4 already connected may cause

operation to become unstable. In this case, connect the

ZERO4 after the computer has started up.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Korg Zero 4 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info