Bedienungsanleitung Korg Zero 8 (Seite 7 von 108) (Deutsch, Englisch, Französisch)

668580

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

9. A, B buttons

By pressing the A or B button you can assign this mixer channel to ei-

ther side of the crossfader (crossfader channel A or B).

10. Channel fader

Adjusts the level of the input audio assigned to this mixer channel.

11. EXT1 knob, EXT2 knob, ZERO FX knob, CUE button

EXT1, EXT2: Adjust the return levels from the devices connected to the

EXT1 RETURN jacks and EXT2 RETURN jacks.

ZERO FX SEND: Adjusts the return level from the internal send effect.

CUE: If you turn on the CUE button, the respective return signal will

be sent to the CUE bus.

12. BOOTH volume knob

Adjusts the output level from the BOOTH

OUT jacks. This will output the same

sound as the MASTER OUT jacks.

13. MASTER volume knob

Adjusts the output level from the MAS-

TER OUT jacks.

14. Headphone jack

You can connect headphones to the headphone jack to monitor the au-

dio of the MONITOR bus or CUE bus.

15. MONITOR BAL knob

If this is turned toward CUE, the headphones will monitor the CUE

bus. If this is turned toward MASTER, the headphones will monitor

the MASTER OUT jacks.

16. MONITOR LEVEL knob

Adjusts the headphone volume.

17. SETUP button

Switches the LCD Display to the

MAIN settings page, allowing you to

edit or view various settings.

18. BPM button

Accesses the BPM page in the LCD display, allowing you to turn the

auto BPM detection on/off, select the source, and set the BPM manu-

ally.

19. AUTO button

Turns auto BPM detection on (LED lit) or off (LED dark).

20. TAP button

The timing interval at which you press this button is used to set the

BPM value or as a guide for auto BPM detection.

21. MIDI CONTROL BANK A, BANK B, BANK C, BANK

D buttons

These buttons access the MIDI CONTROL BANK A, BANK B, BANK

C, and BANK D pages. The eight push-knobs and the touch pad can be

used as MIDI controllers to transmit the MIDI messages you assign for

each bank.

22. Push-knobs 1–8

These are controllers used to edit the parameters shown in the LCD

display. When you’re in the MIDI CONTROL page, these can also be

used as controllers to transmit MIDI control messages.

23. LCD display

This display features the TouchView system with a built-in touch

panel. You can use it to select parameters shown in the LCD display,

and also as a controller for touch-pad effects. When you’re in the MIDI

CONTROL page, you can also use the LCD panel as an X/Y pad MIDI

controller.

24. HOLD button

Holds the current value when you’re

operating an effect that uses the touch-

pad.

25. CHANNEL, SEND, MASTER buttons

These buttons access pages where you can adjust the parameters for

each effect.

CHANNEL: Accesses the channel effect, which can be inserted into a

mixer channel. You can specify the mixer channel in which the channel

effect will be inserted, and select an effect program.

SEND: Accesses the send effect, which is applied to the sound sent

from each channel according to its effect send level setting. You can

specify the return level that is sent back to the master bus.

MASTER: Accesses the master effect, which is applied to the sound of

the master bus.

15 16

17 18 19 20

24 25

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Korg Zero 8 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info