Bedienungsanleitung Korg Zero 8 (Seite 12 von 108) (Deutsch, Englisch, Französisch)

668580

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

TIP: If you’ve selected “FireWire AUDIO” or “FireWire AUDIO

+ MIDI,” the output to the FireWire connector will be the

pre-EQ signal of the source connected to the INPUT (LINE)

jacks.

If you’ve made settings in the SETTING page so that the out-

put of the specified channel is other than “PRE EQ,” “PRE

FDR,” or “POST FDR,” those settings will take priority.

Adjusting the input levels

1. Adjust the GAIN knob.

Adjust this knob so that the level indicator does not light red even

when the maximum level is being input.

TIP: If you’re using mic input and have connected a mic that has

a high level, set the MIC GAIN switch to LOW.

Mixing the sounds

1. Use the fader of each mixer channel to adjust its volume

level.

2. Use the PAN knob of each mixer channel to adjust its

stereo position.

Crossfader

You can use the crossfader to crossfade between the sounds you’ve as-

signed to crossfader channels A and B. By using the crossfader you can

perform DJ techniques such as switching instantly between the sounds of

two channels or crossfading smoothly between them.

1. For the mixer channel that you want to assign to

crossfader channel A, press the A button to turn it on

(the LED will light).

You may turn on the A button for more than one mixer channel if de-

sired.

2. For the mixer channel that you want to assign to

crossfader channel B, press the B button to turn it on

(the LED will light).

3. To cancel this setting, simply press a lit button once

again.

If a mixer channel is not assigned to either channel A or B (i.e., if nei-

ther of these LEDs are lit), the sound of that mixer channel will be sent

to the master bus without passing through the crossfader.

Master output / Booth output

The mixed sound is output from the MASTER OUT jacks and the BOOTH

OUT jacks.

The same mixed sound is output from both sets of jacks, but you can use

the MASTER knob and BOOTH knob to independently adjust each one to

a different volume.

Adjusting the volume

1. Use the MASTER volume knob to adjust the volume of

the MASTER OUT jacks.

Adjust the volume to a level that does not cause the level meter to light

red.

2. Use the BOOTH volume knob to adjust the volume of

the BOOTH OUT jacks.

3. Use the MONITOR LEVEL knob to adjust the volume of

the headphones.

Monitoring

Connect headphones to the headphone jack so that you can refer to the

mixed sound or the audio inputs.

CUE

This function lets you monitor your performance through headphones

without outputting it from the MASTER OUT jacks. To monitor the sound

of the CUE bus through headphones, turn the monitor section MONITOR

BAL knob toward the CUE position. In this state, you can leave a fader

lowered but turn CUE on and use your headphones to check the sound

adjusted by EQ and the channel effect; then when you’ve adjusted the

sound to your liking, raise the channel fader to output the sound from the

master outputs.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Korg Zero 8 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info