Bedienungsanleitung Korg Zero 8 (Seite 17 von 108) (Deutsch, Englisch, Französisch)

668580

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

FireWire interface functions

You can connect the ZERO8 to your computer via a FireWire cable and use

it as an audio/MIDI interface.

Note: This device does not supply bus power.

Note: Do not simultaneously connect more than one computer to

the ZERO8.

Note: If you are using a host application such as sequencing soft-

ware, you’ll need to make audio and MIDI device settings.

For details, refer to the owner’s manual of the software you’re

using.

Note: You must connect the ZERO8 to your computer using a

FireWire cable and turn on the power before you start up your

software. Don't disconnect the FireWire cable or power-off

the ZERO8 while the software is running.

Note: If you're using the ZERO8 with Mac OS X, turn off the Sleep

setting and power management settings.

Note: Each input/output device can be used with only one software

application. Multi-client operation is not supported.

Note: Use the included CD-ROM to install the “KORG FireWire

Audio/MIDI driver” into the computer you're using. (☞

p.27)

1. FireWire audio interface

You can use the ZERO8 as an audio interface. This lets you send the

ZERO8’s audio inputs or mixed sound to your computer, and send the

audio outputs from a host application on your computer to the ZERO8.

Your FireWire-connected computer will detect the ZERO8 as an audio in-

terface that provides a maximum of 16-in and 16-out audio streams.

Limitations for different sampling rates

If the ZERO8 is connected to your computer, you’ll be able to change the

sampling rate from the control panel of the host application or audio

driver. The available number of effects and mixer channels will depend on

the sampling rate you select.

44.1 kHz or 48 kHz: Eight stereo channels + the internal effects

(ZERO FX CHANNEL, SEND, MASTER)

96 kHz: Eight stereo channels

Note: When operating at 96 kHz, the internal effects (ZERO FX

CHANNEL, SEND, MASTER) and the channel EQ for

channels 5–8 will not be available. Nor will you be able to use

the EXT1 or EXT2 RETURN jacks.

Note: When using the ZERO8 with Mac OS X

Depending on the system you’re using, you may experience

problems such as the operating system becoming unstable

when you switch the sampling frequency.

If this occurs, you can start up as described below so that the

ZERO8 will operate with a fixed sampling frequency. In this

case, you won't be able to switch to another sampling fre-

quency from the computer.

44.1 kHz: Turn on the power while holding down the mixer

channel 1 Cue button.

48 kHz: Turn on the power while holding down the mixer

channel 2 Cue button.

96 kHz: Turn on the power while holding down the mixer

channel 3 Cue button.

In the Mac OS System Settings / Sound / Output dialog box,

verify that the ZERO8 has disappeared from the list of sound

output devices, and then turn the power on once again.

Depending on the type of computer you’re using, starting up

the computer with the ZERO8 already connected may cause

operation to become unstable. In this case, connect the

ZERO8 after the computer has started up.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Korg Zero 8 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info