620515

Kraft GUS 650 - 05166 Seite 27

27
Zoom out
Zoom in
Vorherige Seite
1/29
Nächste Seite
Engine power Noise
Revolutions Grinding disk diameter
Maximum blade width Drill diameter
Operation
Sharpening of drills:
An appropriately sharpened drill is characterised by;
Spiky point in the middle of the drill.
Lip with two sharp and identically sized sides.
Two back edges that are slightly lower than the
front edges of the lip.
If your drill does not look like as specified above, it must be
sharpened. Rough sharpening on a desk grinder followed
by drill grinder is recommended for sharpening of skewed
or very blunt drills.
Fit a drill sharpening adapter (3) on the multi-
purpose sharpener.
Take the vice off the holder on the adapter and
insert the drill (picture 1a).
Tighten the vice slightly so that the drill in the
vice can still be moved a bit.
Fasten the vice at the very bottom into the notch
on the left on the adapter so that the drill point is
directed at the V-guide in the notch (picture 1
b).
Move the drill to the very front of the V-guide
(picture 1c).
Turn the drill so that it fits on the V-guide on all
four sides.
Lift the V-guide and make sure the vice fits at
the very bottom of the notch.
Tighten the vice (picture 1d).
Lift the V-guide and remove the vice.
Put the vice to the vice holder in the middle of
the adapter (picture 1e).
Use the on/off button (1) to put the multi-purpose
sharpener into operation.
Move the vice holder slightly from side to side
(picture 1f).
Turn the vice so that the back side is directed
upwards (picture 1g).
Move the vice holder slightly from side to side
(picture 1f). Do not apply too much pressure as
the drill could get overheated and damaged.
Make sure the drill is sharpened correctly and
corresponds to the three sharp drill points above
(as in picture 1h and not in picture 1i).
Use the on/off button to put the multi-purpose
sharpener into operation. Let the sharpening
stone stop completely and then remove the
adapter.
Sharpening of knives:
Fit a knife and scissor sharpening adapter (2) on
the multi-purpose sharpener.
Use the on/off button (1) to put the multi-purpose
sharpener into operation.
Hold the knife by its handle and put the other
end of the knife cutting edge to the adapter knife
notch (picture 2a).
As soon as the cutting edge touches the
sharpening stone, you must pull the knife to
yourself, while applying slight pressure, so that it
is fully pulled out of the knife notch (picture 2b).
Do not press too much.
Turn the knife and put it to the second knife
notch (picture 2c).
As soon as the cutting edge touches the
sharpening stone, you must pull the knife to
yourself, while applying slight pressure, so that it
is fully pulled out of the knife notch (picture 2b).
Do not press too much.
Check whether the knife is sharpened
sufficiently and repeat the sharpening process if
necessary. Use the on/off button to put the multi-
purpose sharpener out of operation. Let the
sharpening stone stop completely and then
remove the adapter.
Sharpening of scissors
Fit a knife and scissor sharpening adapter (2) on
the multi-purpose sharpener.
Use the on/off button (1) to put the multi-purpose
sharpener into operation.
Open the scissors to full extent.
Insert one cutting edge in the scissor notch so
that the scissors joint and handle of the other
cutting edge are directed to the right (picture
2d).
As soon as the cutting edge touches sharpening
stone, you must move the scissors to the side off
the joint towards the point (picture 2e) while
applying slight pressure. Do not press too much.
Turn the scissors and put the other cutting edge
to the scissors notch (picture 2f).
As soon as the cutting edge touches the
sharpening stone, you must move the scissors
to the side off the joint towards the point (picture
2e) while applying slight pressure. Do not press
too much.
Check whether the scissors are sharpened
sufficiently and repeat the sharpening process if
necessary.
Use the on/off button to put the multi-purpose
sharpener out of operation. Let the sharpening
stone stop completely and then remove the
adapter.
Knives and scissors with smooth cutting
edge can be sharpened only. If you sharpen
knives or scissors with corrugated or special
cutting edges, they will get damaged.
Sharpening of plane and chisel blades:
Fit a plane and chisel blade sharpening adapter
(4) on the multi-purpose sharpener.
Put the blade or chisel on the support plate
(picture 3a). The magnet keeps the processed
material in its place.
The angle between the processed material and
sharpening stone must correspond to the
original angle at the cutting edge of the
processed material.
The sharpening angle can be continuously
adjusted from 20 to 40° by loosening the angle
27
… 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

kraft-gus-650---05166

Suche zurücksetzen

  • wo bekomme ich eine ersatzteilliste für GUS 650 her Eingereicht am 2-2-2017 13:42

    Antworten Frage melden

  • ich brauche eine ersatzteilliste für Gus 650 wo bekomme ichdiese Eingereicht am 2-2-2017 13:40

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Kraft GUS 650 - 05166 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info