Bedienungsanleitung Kranzle Bully 1180 TS (Seite 10 von 19) (Englisch)

716892

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

18 19

Motor protection switch

Motor is protected against overload by means of a motor protection switch.

In case of motor overload or blocking, the motor of the high pressure cleaner

switches o automatically. If motor tends to switch o repeatedly, make sure to

detect appears. Make sure to detect and remedy the cause of the failure.

Replacements and inspection work should only be performed by qualiﬁed

persons when the high pressure cleaner is disconnected from the power

supply, i.e. with plug pulled out from the electrical socket.

Totalstop system

The small quadro series is equipped with a total stop system. After water connecti-

on and high pressure hose connection you switch the high pressure cleaner at the

main switch to "ON", a red signal ligths up. If the main switch is switched on, the

motor is started via a pressure switch when opening the safety trigger gun. When

closing the safety trigger gun the motor is switched o immediately. The high

pressure cleaner remains on standby until the main switch is switched "OFF". After

that, the red lights stops.

High pressure hose and spray device

The high pressure hose and spray device which are part of the bully-series

equipment, are made of high quality material and engineered to conform with the

operating conditions of the high pressure cleaner and are duly labeled.

If replacement parts are required, only such parts that are authorized by

the manufacturer may be used. The warranty is automatically void if spare

parts of third-party providers are used! The high pressure hose and spray

device must be connected in a pressure-tight manner (without leakage).

The high pressure hose may not be driven over, pulled excessively, or twi-

sted. The high pressure hose may under no circumstances be pulled over

sharp edges. Defective high pressure hoses must not be repaired (acc. to

DIN 20022) but have to be replaced by new hoses approved by the manu-

facturer.

Prior to putting the high pressure cleaner into operation make sure

that all safety instructions be observed.

Functional details

Water and cleaning system

Water can be connected at mains pressure to the high pressure pump. The water

is then forced under pressure by the high pressure pump to the lance. The high

pressure jet is formed by the nozzle at the end of the lance.

Environmental, refuse disposal and water protection regulations

must be observed!

Safety jet pipe with safety trigger gun

The high pressure cleaner can only be operated when the trigger of the safety

deactivation trigger gun‘s trigger is actuated. When the trigger is pulled, the

safety trigger gun opens. The liquid is then transported to the nozzle. The spray

pressure increases and quickly reaches the operating pressure. When the trigger is

released, the safety trigger gun closes and any further spraying of liquid from the

safety jet pipe is prevented. The stainless steel pressure gauge must show 0 bar.

The increase in pressure when the safety trigger gun is closed causes the pressu-

re control valve-safety valve to open. The motor is switched o by the pressure

switch. When thesafety trigger gun is opened, the pressure control valve - safety

valve closes, the motor is started and the high pressure pump resumes pressure

spraying from the safety jet pipe with the selected operating pressure.

The safety trigger gun is a safety device. Repairs should only be perfor-

med by qualiﬁed persons. Should replacement parts be required, use

only components authorized by the manufacturer.

Pressure control valve - safety valve

The pressure control valve - safety valve protects the high pressure cleaner from

a build up of excess pressure, and is designed not to permit an excess pressure

to be selected for operation. The limit nut on the handle is sealed with a spray

coating. The operating pressure and spray rate can be steplessly adjusted by

turning the handle.

Replacements, repairs, new adjustments and sealing should only

be performed by qualiﬁed persons.

Functional details

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kranzle Bully 1180 TS Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kranzle Bully 1180 TS

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info