Bedienungsanleitung Kranzle e-therm 603 M 36 (Seite 19 von 29) (Englisch)

716903

Zoom out

Zoom in

Vorherige Seite

1/29

Nächste Seite

36 37

Taking out of operation

1. Switch off the high-pressure cleaner

2. Cut off the water supply

3. Open the safety trigger gun catch briefly until the pressure is released

4. Apply safety catch on the trigger gun

5. Remove high-pressure hose and safety trigger gun

6. Emptying high-pressure pump: Hold high-pressure hose and switch

motor on until water jet stops escaping at the outlet.

7. Pull the plug from the socket

8. Clean high-pressure hose and wind up without loops, fix hose drum

9. Clean and wind up the power supply cable

10. Clean the water inlet sieve

11. Apply locking brake

12. Store high-pressure cleaners in frost-free rooms in winter

Particular rules, directives and inspections

Care and Maintenance

Frost protection (e-therm 603 M 36, e-therm 873 M 48)

For protecting the high-pressure cleaner against frost please empty it completely.

Separate high-pressure cleaner from water supply and switch it on. By opening

the safety trigger gun the high-pressure pump presses water out of the water

tank. However, do not allow the high-pressure cleaner to operate without

water for more than one minute. Fill the anti-freeze agent into the water box

and turn on the high-pressure cleaner. Wait with opened gun until the agent

spurts out of the nozzle.

Inspections performed by Kränzle

- Measurement of earth line resistance

- Measurement of voltage and current

- Inspection of tension consistency with +/- 1530 V

- Pressure check of heating coil at 300 bar

- Visual and functional check as per the inspection sheet provided

- Exhaust fume analysis (see test strips provided)

Guidelines for liquid sprayers

The machine conforms with the "Guidelines for liquid sprayers". These guidelines

are issued by the organisation of trade associations and may be obtained from

Carl Heymann-Verlag KG, Luxemburger Str. 49, 50939 Köln. These guidelines

specify that this machine is to be inspected by qualified personnel whenever

necessary, but no less than once every 12 months. These inspections must be

recorded in the inspection log at the end of this manual.

Duties of owner

The owner is to ensure that all safety-relevant components are in a serviceable

condition before the sprayer is used. (e.g., safety valves, hose and electric cables,

spray equipment etc.)

Yearly, or after approx. 500 hours of operation:

- Check flow heater for scale, descale if necessary.

- Change the oil See chapter „General rules“ in these Operating Instructions.

The machine must be disconnected from the power supply when servicing

work is being carried out. The main switch should be in position "0" and the

plug out of the socket.

Frost protection (e-therm 500 M 18, e-therm 500 M 24)

For protecting the high-pressure cleaner against frost please empty it completely.

Separate high-pressure cleaner from water supply and switch it on. By opening

the safety trigger gun the high-pressure pump presses water out of the water

tank. However, do not allow the high-pressure cleaner to operate without

water for more than one minute.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kranzle e-therm 603 M 36 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kranzle e-therm 603 M 36

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info