Bedienungsanleitung Kranzle Therm 875-1 (Seite 14 von 31) (Englisch)

508533

Zoom out

Zoom in

Vorherige Seite

1/31

Nächste Seite

26 27

Functional details Functional details

Check the line fusing and have the voltage and the available current

intensity checked by an expert in case of uncertainty (see technical data).

Electrical connection

The machine is supplied with a power supply cable. The mains plug must be

fitted to a standard grounded socket with a 30 mA residual current operated

device. Connection up to the mains must be carried out by a properly trained

electrician and must comply with the requirements of IEC60364-1. The socket

must be protected with a 16 A fuse on the mains side. When using an extension

cable, this must have an earthed lead which is properly connected to the socket.

The conductors in the extension cable must have a minimum cross section of

1.5 mm². Plug connections must be of a spray-proof design, and may not be

located on a wet floor. For extension cables of more than 10 m in length,

the minimum cross-section must be 2.5 mm²! When using a cable drum,

the power supply cable always must be unwound all the way.

Please note: Lack of water

Lack of water occurs more often than you

probably believe. The more powerful a high-

pressure cleaner is the greater is the danger

that a lack of water occurs. If there is only

an insufficient amount of water available,

cavitation (water-gas mixture) arises inside

the high-pressure pump, which is normally

noticed too late or even not at all. The high-

pressure pump will be destroyed. Please

check the available quantity of water by fil-

ling a bucket with liter scale for one minute.

Required minimum quantity of water (see technical data).

If the metered quantity of water is too small, you have to use a

different water connection, guaranteeing the necessary output.

Lack of water leads to an accelerated wear of the joints (no warranty).

Never let the high-pressure pump run dry for more than 60 seconds.

Water supply

Please pay attention to the regulations of your waterworks compa-

ny! In accordance with DIN EN 61770, the high-pressure cleaner may

not be directly connected to the public drinking water supply lines.

A brief connection however is permissible according to DVGW

(German Association for Gas and Water Affairs) if a non-return

valve with tube ventilator (Kränzle item no.: 410164) is built into the

water supply. Once the water has passed through the non-return

valve it is no longer considered as drinking water. Also indirect

connection to the public drinking water supply lines is permissible

by way of free emission in accordance with EN 61 770; e.g. by using

a reservoir with a float valve. Direct connection to a non-drinking

water supply line is permissible.

Insufficient quantity of electricity

If there are too many collectors in your

proximity connected to the network at the

same time, the available voltage and the

current intensity may decline. Consequently

the motor of the high-pressure cleaner does

not start or even blows. The power supply

may also be insufficient if the power supply

cable is too long or too thin. If extension

cables are too long, this may lead to a

voltage drop causing malfunctions or

start-up difficulties.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kranzle Therm 875-1 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kranzle Therm 875-1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info