Bedienungsanleitung Kratki Orbit (Seite 27 von 338) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

813949

Zoom out

Zoom in

Vorherige Seite

1/338

Nächste Seite

2. STOVE PREPARATION

- Open all air supplies/dampers in the replace

- Stack the larger billets in alternate directions on the bottom of the hearth

- Put a layer of smaller splints on the top of the thick billets for kindling (not more than 3 layers). Arran-

ge the splints so that there is some space between them to let the air ow freely

- Place the tinder on the top layer

BURNING

Strike a light and close the replace door. Depending on how long the chimney ue is and how strong

its draught is, lighting may take from a few to dozen plus minutes. If the chimney draught is not su-

cient, let some air in by opening the replace door slightly. It might be a good idea to open a window

slightly in the room in which the replace is installed to supply larger amount of air to the appliance

(the appliances without integrated external air intake only)

The replace insert is designed to burn wood with a humidity of up to 20%. Using coal, coke, coal-ba-

sed products, plastic, litter, cloths and other ammable materials is not allowed.

Burning approved wood briquettes made of wood dust or pellet is temporarily allowed, but in small

quantities only.

The following is practical guidance for assessing the wood used as fuel. The wood which is to have a

humidity of 18-20% must be seasoned for 18-24 months or kiln-dried. As the humidity of wood de-

creases, its net caloric value rises, which brings nancial savings of even up to 30% of the total wood

weight needed to run the appliance during one heating season. If the wood used for burning is of too

high humidity, then, too much energy needed for evaporation and condensation in the ue pipe or

combustion chamber can be consumed, which aects the heating process of a room.

Another negative process occurring when the high-humidity wood is used is the emission of creosote,

a deposit which damages the chimney ue and, in extreme cases, can result in ignition and a chimney

re.

It is therefore recommended to use hardwood like oak, beech, hornbeam or birch. Lower caloric va-

lues are typical of the coniferous trees and burning their wood produces heavy soot accumulation

on the glass.

CAUTION! It is allowed to run the replace insert without a housing during a trial startup only.

NORMAL STOVE BURNING AND EXTINGUISHING

To prevent ue gases from escaping during the heater’s operation, the door should be closed at all

times, except for lighting, fuel loading and removing ash. The maximum air supply must be provided

when lighting the re. The primary air-supply control must be opened entirely. A slight opening of the

door is allowed until the re is lit. Do not leave the site while lighting the re when the door is open.

Do not use inammable liquids, grease or other improper agents as a lighting aid. Once the stove has

been lit and in normal operation, the burning parameters may be controlled by means of the primary

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kratki Orbit Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info