Bedienungsanleitung Kress asx 132 1 (Seite 12 von 66) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

386782

Zoom out

Zoom in

Vorherige Seite

1/66

Nächste Seite

12 English ASX 132/1

Mechanical 2-speed selector

For battery equipment, the mechanical 2-speed selec-

tor permits optimal drilling torques of 0–1600 rpm in

2nd speed and with high transmission in 1st speed

(0–470 rpm) very high tractive power even with

screws of a large diameter. The switchover is per-

formed by moving the switch 3 until it stops in position

1 or 2.

Torque selection

The battery-driven rotary screwdriver is equipped with

a seven-stage mechanical torque selection. The start-

ing torque for a particular screw is set at the adjusting

ring 4 according to the scale.

The volume of the torque is dependent on various fac-

tors – type and hardness of the material to be proc-

essed, type and length of the screws to be used, but

in addition the demands made on the screw connec-

tion. The data contained in the following table should

be observed as a guideline:

Stage 1 = approx. 1 Nm: screws Ø 3 mm

Stage 2 = approx. 2 Nm: screws Ø 3.5 mm

Stage 3 = approx. 3 Nm: screws Ø 4 mm

Stage 4 = approx. 4 Nm: screws Ø 4.5 mm

Stage 5 = approx. 5 Nm: screws Ø 5 mm

Stage 6 = approx. 6 Nm: screws Ø 5.5 mm

Stage 7 = approx. 7 Nm: screws Ø 6 mm

When the set torque is reached it is signalled acousti-

cally through the construction of the torque coupling.

The coupling disengages with a click.

Operation of the

Quick Clamping Drill Chuck

Rotational direction switch in the LOCK position ■.

The fully automatic spindle locking makes possible

quick and easy changing of the tool in the drill chuck.

Opening: Turn the sleeve in the “AUF” direction.

Clamping: Open the chuck and insert the tool as far

as possible.

Firmly clamp the chuck by turning the

sleeve in the “ZU” direction.

For soft drill shafts, it may be necessary to retighten

after a short time.

Caution! For reasons of safety, take the bat-

tery out of the device for all installation and

removal operations!

Drilling

When drilling, set the torque ring to the “drill” symbol.

The torque coupling is deactivated. Maximum torque

is available for drilling.

When drilling steel, take care that no swarf

enters the ventilation slits of the housing, as

these are attracted by the permanently active

magnet of the motor and would remain on the

motor.

Screwing

Make sure that the bit and screw correspond in size

and shape.

It is advisable to use socket-head screws since their

self-centering action ensures safe work.

Or even better – TORX screws and the corresponding

bits. Optimal screwing is achieved when the screwing

device is fixed securely in the screw head.

Dismounting the Drill Chuck

Rotational direction switch in the LOCK position ■.

Remove the left-hand threaded screw that secures

the drill chuck on the drill spindle against unscrewing

in left rotation. The drill chuck can then be loosened

by lightly striking a Allen key clamped in the drill chuck

and screwed off.

Remounting takes place in the reverse order.

Clean the flat surfaces on the drill chuck and spindle

before mounting. Screw on the drill chuck firmly and

secure with the safety screw.

Observe in addition that, when using a rim gear drill

chuck, the chuck key must not be attached to the

machine with chains, cords or similar means.

When drilling or screwdriving, secure the work

pieces against being rotated by the drill.

8 Practical Tips

ASX 132/1 - Buch Seite 12 Montag, 27. März 2000 1:29 13

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kress asx 132 1 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info