Bedienungsanleitung Kress wts 900 e (Seite 8 von 52) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

390656

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

English 900 WTSE

The angle grinder can be used universally for cutting

and treating metals and stone. For high speeds, only

use the cutting and grinding items approved for the

machine.

Before operating the machine, please read through

the operating instructions completely, follow the

Safety Instructions

in this manual as well as the gen-

eral

Safety Instructions for Power Tools

in the

accompanying booklet.

Important instructions, which should be read

before starting operation, and which we strongly

recommend observing:

If the mains cable is damaged while working, pull

the mains plug immediately.

Never work with a damaged mains cable.

Wear protective glasses, hearing protection, pro-

tective gloves and sturdy shoes.

The dust that is produced while working is detri-

mental to health. Use dust extraction and wear a

dust mask.

The machine must be used only for dry cutting/

grinding.

Do not work with materials containing asbestos.

Do not carry the machine by the cable.

Always hold the machine firmly in both hands and

take a firm stance.

Always conduct the cable away to the rear of the

machine.

Only insert the mains plug into the socket when

the machine is turned Off.

If the mains plug is pulled out, of if there is a power

cut, unlock the On/Off switch immediately and set

it to the Off position in order to prevent it from

starting to run again in an uncontrolled manner.

The auxiliary handle serves for your safety. Work

with the additional handle mounted.

Only do cutting and grinding work with the protec-

tive guard mounted!

The dust produced when treating stone with crys-

talline silicic acid is hazardous to health. Use a

dust extractor and wear a dust mask. The dust

extractor must be suitable for vacuuming stone.

For clamping the grinding discs, clamping flanges

may only be used that are the same size and

shaped to fit the contacting surface. Please

observe the instructions for using the clamping

flange in the operating manual. Intermediate

layers may not be used on conical or depressed-

centre grinding discs.

When clamping depressed-centre grinding tools

the diameter of the clamping flange must be at

least 5 mm smaller than the diameter of the flat

depressed-centre surface of the grinding tool;

here, the clamping flange must not press onto the

transitional radius of the clearance.

The location bore of the grinding tools may not be

drilled afterwards as there is risk of fracture.

Grinding tools may on no account be operated at

a speed higher than that stipulated by the grinding

tool manufacturer.

Only fibre-reinforced grinding discs or diamond

cutting discs may be used.

The grinding discs etc. intended for use must be

approved for a peripheral velocity of 80 m/s!

Formula:

d = Diameter of the grinding disc in mm

n = No-load speed/min.

(see identification plate)

m/s = Peripheral velocity in metres per second

A new grinding tool and any grinding tool that is

re-mounted, must run on the machine intended for

use at no-load for 30 seconds. Operating person-

nel and any other persons must stand outside the

danger area during the test run.

The machine may only be brought into contact

with the work piece once it has been switched on.

Caution! Be careful of rotating grinding tools.

Pay attention to the direction of rotation: Always

hold the machine such that the grinding dust or

sparks fly away from the body. When grinding

metal, sparks can occur. Be careful if persons or

objects are standing nearby. Inflammable material

must not be kept in the vicinity.

Check the working area with a metal detector in

order to avoid damaging any concealed electrical

leads, or water and gas pipes.

Switch the machine off immediately if the cutting

disc should jam (jerky reaction force).

Do not use any cutting discs for rough grinding.

Grinding tools may not be brought to a standstill

by pressing against the periphery or grinding face

of the grinding tool.

Do not clamp the machine in a vice.

Observe the instructions for assembly and opera-

tion provided by the manufacturer of the grinding

tool.

1 Application

Safety Instructions and

Accident Prevention

d · 3.14 · n = m/s

6000

900 WTSE - Buch Seite 8 Donnerstag, 28. Juni 2001 2:52 14

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kress wts 900 e Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info