Bedienungsanleitung Krups Essential EA815 (Seite 15 von 74) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

807146

Zoom out

Zoom in

Vorherige Seite

1/74

Nächste Seite

■A screen indicates that the appliance is heating up. Once the appliance has finished heating up, you can begin to

make steam by pressing START , and following these steps (13):

Step 1: holding the milk jug in place, insert the steam nozzle approximately 2 cm into the milk and wait for it to

start frothing.

Step 2: raise the container slightly (approximately 1 cm). Do not completely submerge the metal tube.

Step 3: gradually lower the container as the froth accumulates. (14)

■When you have frothed the milk enough, press the STOP button to stop the cycle. Warning: the cycle does not

stop immediately.

■To remove any milk traces from the steam nozzle, place a container under the nozzle and start the steam function

again (approximately 10 seconds).

■The steam nozzle is removable in order to allow for deep cleaning. Wash it with water and a little non-abrasive

detergent using a brush. Rinse and dry (15-16). Before replacing, make sure that the air holes are not clogged with

milk residue. Unclog the holes with the needle supplied with your appliance if necessary (17).

■To stop the steam, press the STOP button .

WARNING: THE CYCLE DOES NOT STOP IMMEDIATELY.

Steam can be produced for a maximum of 2 minutes per cycle.

Auto-cappuccino XS 6000 set (sold separately)

■This auto-cappuccino accessory enables you to make cappuccinos or lattes (18). Connect the different parts to

each other. Ensure that the pipe is not pierced by keeping the knob in the correct place.

■After removing the lid, fill the jug with milk (19) and place a cup or glass under the auto-cappuccino nozzle (20).

Select cappuccino or latte on the special nozzle (21).

■Start steam, as indicated in the chapter Making drinks with steam.

■Once you have made the milk froth, place your cup under the coffee jets and start a coffee cycle (22).

To prevent the milk from drying on the auto-cappuccino accessory, ensure that you clean it thoroughly. You are advised

to wash it immediately by running a steam cycle with the accessory jug filled with water in order to clean the inside

of the nozzle. For this you can use the KRUPS liquid detergent available separately.

Emptying the coffee grounds collector and the drip tray

■If the symbol starts flashing, empty and clean the drip tray (the drip tray may contain coffee grains) and the coffee

grounds collector (23-25).

■The drip tray is fitted with floats which indicate when it needs to be emptied (26). Once you have removed the coffee

grounds collector, you should empty it completely in order to avoid any overflow.

■The warning message will continue to be displayed if the coffee grounds collector is not pushed in or inserted

correctly (24). You cannot make an espresso or a coffee while the warning message is shown.

Rinsing the circuits :

Press the maintenance and settings button (27). The function indicator is shown above the maintenance button

If necessary, using the navigation button, select the rinse symbol .

Press START , rinsing starts and finishes when the coffee menu appears.

MAINTAINING YOUR APPLIANCE

Preparing the grinder

You can adjust the strength of your coffee by adjusting how finely the coffee beans are ground.

Generally, the finer the coffee is ground, the stronger and creamier the coffee will be, but this also depends on the

type of coffee used.

Adjust the fineness of grinding by turning the coffee grounds fineness adjustment knob which is located in the

coffee bean container. It is advised that you do this during grinding, one notch at a time.

After 3 rounds, you will notice a pronounced difference in taste. To the left, the grounds are finer. To the right, the

grounds are courser. (7)

Claris F 088 - Aqua Filter System cartridge (Sold separately)

To optimise the taste of your drinks and the lifespan of your appliance, you are advised to only use a Claris - Aqua

Filter System cartridge with your machine (see the chapter OTHER FUNCTIONS – Installing the filter).

Every time you place a Claris-Aqua Filter into the machine you must prime the filter before using the machine by

activating the “install filter cartridge” program.

Note :

The amount of water for making an espresso is between 30 and 70 ml.

The amount of water for making a coffee is between 80 and 180 ml.

Starting preparation (with 1 or 2 cups)

■Press the on-off button , and wait for the appliance to finish heating up.

■The coffee types menu is displayed. The function indicator is shown above the coffee types button (6).

■Place one or two cups under the coffee jets. You can lower or raise the coffee jets according to the size of your cup

(8). Select the coffee strength (shown coffee beans displayed on the screen in brackets) with the + button to

increase or the - button to decrease. (9).

■Press the navigation button to set the volume: select the volume of water displayed on the screen between

brackets using the + or - buttons (10).

■Press the navigation button to set the number of cups: select 1 or 2 cups, displayed on the screen between

brackets using the + or - buttons .

■Press the START button (11).

■You can set the water volume at any time using the + or - buttons .

■To stop the flow into your cup, press the STOP button .

■You can also adjust the temperature of your coffee (see the chapter OTHER functions - Settings).

Two cup function

The appliance will automatically carry out 2 full cycles of coffee preparation.

MAKING AN ESPRESSO AND A COFFEE

Steam is used to froth the milk, for example when preparing a cappuccino or caffe latte, and also to heat up liquids.

As a higher temperature is required when producing steam than when making an espresso, the appliance will launch

an additional pre-heating phase.

Frothing milk

■For best results, you are advised to use very fresh, very cold pasteurised or UHT milk, recently opened. Unpasteurised

milk does not produce the best results.

■Check that the steam nozzle is correctly positioned.

■Pour the milk into a milk jug which has a handle or into a cappuccino cup. Only fill it half way.

■When the screen displays the drink selection menu, press the steam button (12). The function indicator is

located above the steam button .

■Insert the steam nozzle into the milk.

MAKING DRINKS USING STEAM

Krups Essential EA815 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info