Bedienungsanleitung Krups EVIDENCE EA89011 (Seite 25 von 306) (Alle Sprachen)

672686

Zoom out

Zoom in

Vorherige Seite

1/306

Nächste Seite

Installing the cartridge in the appliance: Screw the lter cartridge into the bottom of the water tank using the

accessory supplied with the cartridge. Fig. 4

Set the month when the cartridge is tted (position 1 on the illustration, left side gure in the opening) by turning the

grey ring located on the upper end of the lter. The month when the cartridge should be replaced is indicated in position

2 on the illustration. Fig. 5.

Put a container of 0.6 l under the steam exit. Fig. 6.

The machine must be primed whether the lter has been installed or not. This means that the water circuits have to

be lled. To do this, follow the instructions provided on the screen. The machine will begin by lling the water circuits,

preheating the circuits and then will complete an automatic rinse.

The screen will inform you when installation is complete.

Water hardness

You must set your machine depending on the hardness of your water, from 0 to 4. To do this, follow these instructions:

Before using the appliance for the rst time, check the hardness of your water so that you can set the appliance

accordingly. This operation should also be carried out when you use your machine in a place where the hardness of

the water is different or if you notice a difference in the hardness of the water. To check the water hardness, use the

test strip supplied with your machine or contact your local water authority.

The details of the classes are given in the table below:

Degree of hardness

Class 0

Very soft

Class 1

Soft

Class 2

Average hardness

Class 3

Hard

Class 4

Very hard

° dH < 3° > 4° > 7° > 14° > 21°

° e < 3,75° > 5° > 8,75° > 17,5° > 26,25°

° f < 5,4° > 7,2° > 12,6° > 25,2° > 37,8°

Appliance setting 0 1 2 3 4

Fill a glass of water and insert a strip. Fig. 2

After 1 minute read the level of water hardness. Fig. 3

Indicate the number of red zones when conguring the appliance.

Preparing the appliance

Remove and ll the water tank. Fig. 7.

Replace the water tank. Fig. 8.

Remove the lid of the coffee bean container and add coffee beans (max. 250 g). Fig. 9.

Replace the lid of the coffee bean container. Fig. 10.

BEFORE PREPARING DRINKS

IMPORTANT INFORMATION

Depending on the drinks chosen, your Espresso Automatic EA89 will automatically adjust the quantity of ground coffee.

Preparing the grinder

You can adjust the strength of your coffee by adjusting how nely the coffee beans are ground. In general, the ner the

coffee is ground, the stronger and creamier the coffee will be. It may also vary according to the type of coffee used.

We recommend a ne setting for espressos and a coarser setting for coffees.

Adjust the neness of grinding by turning the coffee grounds neness adjustment knob (J) which is located in the

coffee bean container. This setting should be applied during grinding notch by notch. After 3 rounds, you will notice a

pronounced difference in taste.

Setting the neness of grinding is useful when you change the type of coffee or if you want to make coffee that is more

or less strong. However, it is not advised to use this setting systematically.

Adjusting the coffee outlet

For all the drinks available, you can lower or raise the coffee outlets according to the size of your cup or glass. Fig.11

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Krups EVIDENCE EA89011 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info