Bedienungsanleitung Krups YY3069 - Espresseria (Seite 24 von 187) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

700530

Zoom out

Zoom in

Vorherige Seite

1/187

Nächste Seite

ENGLISH

now prepared your appliance. The drink select menu will be displayed.

Put two cups under the coffee outlets. You can lower or raise the coffee outlets to suit the

size of your cups.- Fig. 17. Select your drink and conrm by clicking twice on the OK key.

A message will appear to tell you that you have chosen two cups.

The appliance will automatically sequence 2 complete coffee-making cycles.

PREPARING HOT WATER

While the screen displays the drink selection menu, press the “hot water” key .

A message will invite you to place a container under the steam nozzle. Again press the “hot

water” key to produce hot water - Fig. 14.

To interrupt the steam function, just press any key.

If the nozzle is blocked, clean it out with a ne needle.

The maximum amount of hot water per cycle is limited to 300 ml.

PREPARING STEAM

Steam froths up the milk to make a cappuccino or a caffe latte, for example, and also heats

up liquids. As you need a higher temperature to produce steam than to make an espresso,

the appliance runs an additional pre-heating phase for steam.

While the screen displays the drink selection menu, press the “steam” key - Fig. 18. A

screen will inform you that the appliance is being pre-heated. Once the pre-heating phase

has been completed, a message will ask you to place a container under the steam nozzle

- Fig. 5. Press the “steam” key again to start generating steam. A little water will be

produced rst and then steam will start. Use the same key to stop steam generation.

BE CAREFUL, BECAUSE THE CYCLE DOES NOT STOP IMMEDIATELY.

Frothing milk

We recommend that you use pasteurised or UHT milk that has been recently opened.

Do not use untreated milk. After the steam function has been used, the nozzle will be

hot, and we recommend that you wait for a few moments before handling it.

Check that the steam nozzle is correctly tted - Fig. 19.

Pour the milk into your milk jug. Only half ll it. Immerse the nozzle in the milk - Fig. 20.

Press the “steam” key and follow the instructions on the screen.

Once your milk is frothy enough… - Fig. 21, again press the “steam” key to stop the

cycle. Be careful, because the cycle does not stop immediately.

To remove any remaining milk from the steam nozzle, place a container under the nozzle

and press the “steam” key . Let the hot water escape for at least 10 seconds and then

again press the “steam” key to stop water.

You can remove the steam nozzle for thorough cleaning. Wash it using a brush with water

and a little non-abrasive washing up liquid. Rinse and dry it - Fig. 22-23. Before re-tting,

make certain that the air inlet holes are not clogged by milk residues. Clean out the holes

with a needle if necessary - Fig. 24.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Krups YY3069 - Espresseria Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info