Bedienungsanleitung Ksenia Lares 4.0 (Seite 29 von 58) (Englisch)

693399

Zoom out

Zoom in

Vorherige Seite

1/58

Nächste Seite

lares 4.0 PROGRAMMING MANUAL

rev. 0/2018

System

In this section, you can manage what you have created so far, creating custom events, arming modes, scenarios,

associating the zones with devices, etc.

In this page, you can create the arming modes of the partitions that will be subsequently assigned to the "Scenarios".

The scenarios will be, in turn, associated with speciﬁc "events".

To program the arming modes, click on the icon (

) and then on the symbol ( ). Then associate a label to the

arming mode (e.g. total, disarming, etc.) and set the colours that identify the arming mode of the zone.

The colours are divided as follows:

• White: no action. When the mode is activated, the status of the partition is not changed.

• Yellow: arm with delay. When the mode is activated, the partition is armed but the entry and exit times are valid

(only for the partition zones that are also delayed).

• Red: arm. When the mode is activated, the partition is armed and both entry and exit times are reset.

• Blue: switched. When the mode is activated, if the partition is armed, it is disarmed and vice versa.

Note: the switched arming mode can be used several times; in other words, it is possible to carry out the arming and

disarming cycles of the partition with a single scenario (e.g. arm disarm arm disarm etc.). If the partition is

programmed with delays, it will only be armed with delays (it is not possible to switch to an instant input).

In this example we have:

• Input 1: partitions 1 and 4 armed with delays. Partitions 2 and 3 armed instantly.

• Input 2: partitions 1 and 4 armed instantly.

The status of the partitions 2 and 3 remains unchanged (if they were previously armed they would remain armed, if

they were disconnected they would maintain this status).

• Input 3: all partitions are disarmed.

• Input 4: partitions 2 and 3 armed instantly. The status of the partition 4 remains unchanged.

If the partition 1 was disarmed, it is now armed and vice versa.

Outputs

To program the outputs, click on the icon ( ) and then on the symbol ( ). Then enter the various parameters:

• Description: the name given to the output (e.g. boiler, living room light, garage automation, etc.)

• Hashtags: see the Hashtags section in (page 19) of the manual. You are able to associate multiple hashtags.

This function is useful when you want to drive multiple outputs with an event. (e.g. you want to drive output 1, output

2 and output 3, all with the Hashtag “#outdoor lights”. In the page of scenarios, you will need to create an “outdoor

lights” scenario and then “Actions” Type: "Output" Subtype: "Output activation" Entity: "#outdoor lights".

This scenario will be associated with an event (e.g. partition alarm). Refer to the "Scenarios" section in (Page 41)

• Partitions: the exit is associated with the partitions. For example, it is useful when you want to limit the management

of the exit by the users (e.g. the system built in a semi-detached villa).

Arming modes

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ksenia Lares 4.0 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info