Bedienungsanleitung Ksenia Lares 4.0 (Seite 33 von 58) (Englisch)

693399

Zoom out

Zoom in

Vorherige Seite

1/58

Nächste Seite

lares 4.0 PROGRAMMING MANUAL

rev. 0/2018

Processing mode

After having associated the zone with the device, the type of analysis of the signal required to generate an alarm is

determined.

Note: some modes may not be usable depending on the type of device selected (e.g. on the lares 4.0 board, only the

standard and command modes will be available)! For convenience, all available conﬁgurations will be shown.

There are four modes:

1. Standard: to be combined with contacts, detectors, etc.

Note: not available for unum WLS, velum WLS, nebula WLS, auxi WLS.

2. Command: this zone does not generate alarms, but is only used to activate scenarios.

To program a command zone, associate the partitions to be armed/disarmed with the zone.

Subsequently, in the "Events" page, associate the real-time zone (alarm) with the scenario to be activated.

If all the partitions managed by that scenario are not associated, only the selected partitions will be armed/disarmed.

If this option is activated, it is possible to directly manage an output (or a group of outputs using a Hashtag) without

creating a scenario. In this case, the following additional conﬁgurations are displayed:

a. Command output: in this menu, it is possible to select the output (or the group of outputs via Hashtag) that you

want to be managed by the command zone

b. Type of activation: in this menu, it is possible to select the type of action to be performed on the output: activation,

deactivation, switching (with respect to the current status)

c. Command mode: in this menu, it is possible to select the type of command between the button (the action on the

output will be carried out only when the zone is opened) and switch (the action is performed both at the opening

and closure of the zone)

N.B.: This feature is not available for unum WLS, velum WLS, nebula WLS, auxi WLS.

3. Inertial/Glass break: to be combined with seismic, glass break detectors etc.

Not available for lares, ergo-rev.0, duo, unum WLS, nanus WLS, velum WLS, nebula WLS, auxi WLS.

4. Shutter: to be combined with detectors for shutters (e.g. contact ropes etc.)

Not available for lares, ergo-rev.0, duo, unum WLS, nanus WLS, velum WLS, nebula WLS, auxi WLS.

• Test: If this option is selected, only events in the event log will be traced without generating an alarm.

• Input delay: Select this option if you want the violation of the zone to trigger the initiation of the input time (or if this

time has already been started, ensure that the alarm is not triggered). It is possible to establish an entrance path on

multiple levels by programming the input level parameter. For example, when partitions are armed, if you program

three levels, you have the following behaviour:

1) at active warning time: it is possible to breach only the zones one level higher than the last breached zone.

2) at inactive warning time: it is possible to breach only the zones of level 1; the warning time starts at the ﬁrst

breach.

The ﬁgure shows a hypothetical situation of entrance into a house where the control panel of the system can be reached

only after having intercepted some areas.

Speciﬁcally, the volumetric sensor marked with ( 1 ) must be the ﬁrst to be violated so as not to generate an alarm. Then,

the number (2) and the number (3) will follow.

Attention: for correct functioning, the zones that intervene in the entrance path must have at least

one partition in common.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ksenia Lares 4.0 Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info