Bedienungsanleitung KTM 250 EXC - 2016 (Seite 109 von 154) (Englisch)

657924

109

Zoom out

Zoom in

Vorherige Seite

1/154

Nächste Seite

17 TUNING THE ENGINE 107

The idle speed is adjusted with adjusting screw



The idle mixture is adjusted with the idle air adjusting screw



500282-01

Idle air range A

Operation with the throttle slide closed. This range is influenced by adjusting screw



and the idle air adjusting screw



Transition range B

Behavior of the engine when the throttle slide is being opened. This range is influenced

by the idling jet and by the form of the throttle slide.

If the engine sputters and smokes heavily when it starts despite a good idle and part-

load setting, and if it abruptly reaches full power at a high rpm, the carburetor setting

is too rich, or the float level is too high or the float needle valve is leaky.

Part-load range C

Operation with the throttle slide partially open. This range is influenced by the jet

needle (form and position). The idle setting influences the engine tuning in the lower

range, and the main jet influences the engine tuning in the upper range.

If, when accelerating with the throttle slide partially opened, the engine only stutters

while running, the jet needle needs to be lowered by one level. If the engine knocks,

especially when it reaches the full performance engine speed while accelerating, the jet

needle needs to be raised. If the behavior described above occurs while idling or just

above idling, the idling system needs to be regulated to a leaner setting if the engine is

stuttering and to a richer setting if knocking.

Full-load range D

Operation with the throttle slide open (full throttle). This range is influenced by the

main jet and jet needle.

If the insulator of a new spark plug is very light or white after a brief ride at full throt-

tle, or if the engine knocks, a larger main jet needs to be used. If the insulator is dark

brown or sooty, a smaller main jet needs to be used.

17.4 Carburetor - adjusting the idle speed

M00588-10

–

Screw idle air adjusting screw



all the way in.

– Turn the idle air adjusting screw to the specified basic setting.

Guideline

Idle air adjusting screw (All 125 models)

Open 2.75 turns

Idle air adjusting screw (All XC-W models, 300 EXC BR)

Open 2.0 turns

Idle air adjusting screw (200 EXC EU)

Open 1.5 turns

Idle air adjusting screw (200 EXC AU)

Open 1.0 turn

Idle air adjusting screw (250/300 EXC AU)

Open 3.5 turns

Idle air adjusting screw (250 EXC EU, 250 EXC Six Days EU)

Open 1.5 turns

Idle air adjusting screw (300 EXC EU, 300 EXC Six Days EU)

Open 1.75 turns

– Run the engine until warm.

Guideline

Warm-up time ≥ 5 min

Danger

Danger of poisoning Exhaust gases are toxic and inhaling them may result

in unconsciousness and/or death.

– When running the engine, always make sure there is sufficient ventila-

tion, and do not start or run the engine in an enclosed space without an

effective exhaust extraction system.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

KTM 250 EXC - 2016 Seite 109

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info