Bedienungsanleitung Kubota B2320 (Seite 31 von 88) (Englisch)

639537

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

15OPERATING THE ENGINE

A Glow plug indicator (5) comes on while engine is being

preheated.

A [HST type]

Because of the safety devices, the engine will not start

except when the PTO gear shift lever is placed in the

"OFF" position, the speed control pedal is placed in the

"NEUTRAL" position, and the clutch pedal is

disengaged.

A [Manual transmission type]

Because of the safety devices, the engine will not start

except when the PTO gear shift lever is placed in the

"OFF" position, the main gear shift lever is placed in

the "NEUTRAL" position, and the clutch pedal is

disengaged.

C Cold Weather Starting

When the ambient temperature is below -5 (23 ) and

the engine is very cold. If the engine fails to start, turn off

the key for 30 seconds. Then repeat steps 8 and 9. To

protect the battery and the starter, make sure that the

starter is not continuously turned for more than 30

seconds.

BBlock Heater (Option)

A block heater is available as an option from your dealer.

It will assist you in starting your tractor when the ambient

temperature is below -15 (5 )

If a lamp is still on, immediately stop the engine and

determine the cause.

STOPPING THE ENGINE

WARMING UP

To avoid personal injury:

A Be sure to set the parking brake during warm-

up.

A Be sure to set all shift levers to the "NEUTRAL"

positions and to place PTO lever in "OFF"

position during warm-up.

For five minutes after engine start-up, allow engine to

warm up without applying any load, this is to allow oil to

reach every engine part. If load should be applied to the

engine without this warm-up period, trouble such as

seizure, breakage or premature wear may develop.

BWarm-up Transmission Oil at Low

Ambient Temperatures

Hydraulic oil serves as transmission fluid. In cold weather,

the oil may be cold with increased viscosity. This can

cause delayed oil circulation or abnormally low hydraulic

pressure for some time after engine start-up. This in turn

can result in trouble in the hydraulic system. To prevent

the above, observe the following instructions:

Warm up the engine at about 50 % of rated rpm according

to the table below:

A Do not operate the tractor under full load condition until

it is sufficiently warmed up.

8. Fully depress the clutch pedal, turn

the key to "PREHEAT" position and

hold it for about 2 to 3 seconds.

Temperature Preheating Time

Over 0 C (32 F) 2 to 3 sec.

0 to -5 C (32 to 23 F) 5 sec.

-5 to -15 C (23 to 5 F) 10 sec.

9. Turn the key to "START" position and

release when the engine starts.

10. Check to see that all the lamps on the

Easy Checker(TM) are "OFF".

11. Release the clutch pedal

1. After slowing the engine to idle, turn the

key to "OFF".

2. Remove the key.

Ambient temperature Warm-up time requirement

Above 0 C (32 F) At least 5 minutes

0 to -10 C (32 to 14 F) 5 to 10 minutes

-10 to -20 C (14 to -4 F) 10 to 15 minutes

Below -20 C (-4 F) More than 15 minutes

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kubota B2320 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info