Bedienungsanleitung Kubota B2620 (Seite 64 von 88) (Englisch)

639538

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

48 MAINTENANCE

C Engine Oil:

A Oil used in the engine should have an American Petroleum Institute (API) service classification and Proper SAE

Engine Oil according to the ambient temperatures as shown above:

A With the emission control now in effect, the CF-4 and CG-4 lubricating oils have been developed for use of a low-

sulfur fuel on on-road vehicle engines. When an off-road vehicle engine runs on a high-sulfur fuel, it is advisable to

employ the "CF or better" lubricating oil with a high Total Base Number (TBN of 10 minimum).

C Fuel:

A Cetane number of 45 minimum. Cetane number greater than 50 is preferred, especially for temperatures below

-20 (-4 ) or elevations above 1500 m (5000 ft).

A If diesel fuel with sulfur content greater than 0.5% sulfur content is used, reduce the service interval for engine oil

and filter by 50%.

A DO NOT use diesel fuel with sulfur content greater than 1.0%.

A Diesel fuels specified to EN 590 or ASTM D975 are recommended.

A No.2-D is a distillate fuel of lower volatility for engines in industrial and heavy mobile service. (SAE J313 JUN87)

A Since this engine adopts EPA Tier 4 and Interim Tier 4 standards, the use of low sulfur fuel or ultra low sulfur fuel is

mandatory in EPA regulated area (North America). Therefore, please use No.2-D S500 or S15 diesel fuel as an

alternative to No.2-D, or use No.1-D S500 or S15 diesel fuel as an alternative to No.1-D if outside air temperature

is below -10 (14 ).

C Transmission Oil:

The oil used to lubricate the transmission is also used as hydraulic fluid. To insure proper operation of the hydraulic

system and to complete lubrication of the transmission, it is important that a multi-grade transmission fluid is used in

this system. We recommend the use of KUBOTA UDT or SUPER UDT fluid for optimum protection and performance.

(Consult your local KUBOTA Dealer for further detail.)

Do not mix different brands together.

A Indicated capacities of water and oil are manufacturer's estimate.

A Refer to the following table for the suitable API classification engine oil according to the engine type (with internal

EGR, external EGR or non-EGR) and the fuel (low-sulfur or high-sulfur fuel).

Fuel used

Engine oil classification (API classification)

Oil class of engines except external EGR Oil class of engines with external EGR

High Sulfur Fuel

( 500 ppm)

(If the "CF-4, CG-4, CH-4 or CI-4" lubricating oil is

used with a high-sulfur fuel, change the lubricating

oil at shorter intervals. (approximately half))

---

Low Sulfur Fuel

(< 500 ppm) or

Ultra Low Sulfur Fuel

(< 15 ppm)

CF, CF-4, CG-4, CH-4 or CI-4

CF or CI-4

(Class CF-4, CG-4 and CH-4 engine oils

cannot be used on EGR type engines)

EGR: Exhaust Gas Re-circulation

A The CJ-4 engine oil is intended for DPF (Diesel Particulate Filter) type engines, and cannot be used on this tractor.

without EGR with external EGR

Model B2320 / B2620 / B2920 ---

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kubota B2620 Seite 64

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info