Bedienungsanleitung Kubota T2080 (Seite 67 von 78) (Englisch)

639541

Zoom out

Zoom in

Vorherige Seite

1/78

Nächste Seite

PERIODIC SERVICE52

[T2080, T2380]

1. The drain plug is located on the starter side of the oil

pan. Clean the area around the oil drain plug and the

oil fill cap/dipstick.

2. Remove the drain plug and the oil fill cap/dipstick.

3. Allow the oil to drain and then reinstall the drain plug.

Tighten 13.6 N-m (10 ft. lb.).

4. Remove the old filter and wipe off the filter adapter with

a clean cloth.

5. Place a new replacement filter in a shallow pan with

the open end up. Pour new oil, of the proper type, in

through the threaded center hole. Stop pouring when

the oil reaches the bottom of the threads. Allow a

minute or 2 for the oil to be absorbed by the filter

material.

6. Apply a thin film of clean oil to the rubber gasket on the

new oil filter.

7. Install the new oil filter to the filter adapter. Hand

tighten the filter clockwise until the rubber gasket

contacts the adapter, then tighten the filter an

additional 3/4-1 turn.

8. Fill the engine with the proper oil to the "FULL" or "F"

mark on the dipstick. Always check the oil level with

the dipstick before adding more oil.

9. Reinstall the oil fill cap/dipstick and tighten securely.

10.Start the engine and check for oil leaks. Recheck oil

level before placing the engine into service.

Stop the engine, correct any leaks, and allow a minute

for the oil to drain down, then recheck the level on the

dipstick.

A To prevent extensive engine wear or damage, always

maintain the proper oil level in the crankcase. Never

operate the engine with the oil level below the "ADD"

or "L" mark or above the "FULL" or "F" mark on the

dipstick.

EVERY 200 HOURS

BCleaning Bendix Starter [T1880]

Consult your local KUBOTA Dealer for this service.

EVERY 500 HOURS

BCleaning Solenoid Shift Starter

[T2080,T2380]

Consult your local KUBOTA Dealer for this service.

EVERY 600 HOURS

BReplacing Transaxle Filter

To avoid serious injury:

A Park the machine on a firm and level surface.

A Apply the parking brake.

A Be sure to stop the engine and remove the key

before changing or checking the oil.

A Allow transmission case to cool down

sufficiently; oil can be hot and may cause

burns.

1. Apply the bypass valve.

2. Remove the hex head bolts (4), and filter guard (3).

Clean any loose debris from around the perimeter of

the oil filter (2).

3. Place an oil drain pan (12" or more diameter and 8 qt.

capacity is optimal) beneath the oil filter. Remove the

oil filter (2) and discard it.

A Always replace the filter when preforming any internal

maintenance to the transaxle.

4. Remove the metal oil drain plug (8) from drain port and

allow any remaining oil to drain from the transaxle.

5. After the oil has drained, inspect all parts for excessive

wear or damage. Replace if necessary. Then install

the metal oil drain plug (8) into transaxle. Torque the

plug (8) to 1.70 N-m (1.25 lbf-ft).

6. Wipe the filter base surface off and apply a film of new

oil to the gasket of the new replacement filter (Hydro-

Gear part number 52114).

7. Install the new filter by hand, turn 3/4 to 1 full turn after

the filter gasket contacts the filter base surface.

(1) Engine oil filter cartridge (A) "MOUNTING SURFACE"

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kubota T2080 Seite 67

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info