Bedienungsanleitung Kuppersbusch EEB 6850.0 (Seite 22 von 26) (Englisch)

661118

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

EEB 6850.8

Attaching the oven door.

– Hold the oven door with both hands and insert the hinges in the corres-

ponding slots. The hinge should ﬁ t snugly.

– Slowly open the door fully.

– Again lower the supports on the door

hinges.

– Close the oven door.

Shelf runner assembly and disassembly

Removing the shelf runners

– Remove the shelf runners by loosening them from the chrome nuts that

are located on the sides of the oven.

– Remove the shelf runner.

Assembling the shelf runners

– Position the shelf runners and attach the nuts.

Folding the heating element down/away

Fold down the heating element (Top heat/Grill)

– Open the lock and fold down the

heating element.

Fold away the heating element.

– Fold away the heating element and

close it again with the lock.

Regeneration of the ökotherm®

catalyst

The ökotherm® catalyst dissolves the grease particles and smells

produced when roasting with the Hot Air cooking setting. This process is

sufﬁ cient with the normal use of the Hot Air setting. In special cases

(well-cooked roasts in large quantities) it is possible that small grease

particles will be deposited on the catalyst. When you use the oven again

e.g. when cooking a pizza, they will be gradually dissolved.

If you believe that the catalyst is not cleaning as well as it should

(it smells a lot) you can regenerate it by eliminating the remains of

accumulated grease.

Regeneration of the ökotherm® catalyst

– Select the Hot Air service function.

– Set the thermostat to 200° C and

– heat the empty oven for 60 mins.

Assistance in the event

of malfunction

Repairs must only be carried out by an authorised professional.

You may be able to solve some malfunctions yourself. First check if there

has been a problem with the way it is being used. Repairs during the

guarantee period are not exempt from costs in the case of an error in

the way it is being used or if you have not noticed one of the following

situations.

What to do if…

... the sensors or lights do not work.

Check: Is the socket plugged in? Is the fuse in good condition? Has there

been a power failure? Is the child safety lock on?

... one or several sensors do not react to contact but it is possible to

connect the lighting.

Possible cause: The sensors continuously adapt their sensitivity to

ambient conditions. In unfavourable circumstances e.g. if someone leans

on them for a long period of time, it may take several minutes until the

sensors react again.

Wait approximately 15 seconds or disconnect and reconnect the fuse.

Repeat the procedure again if necessary.

The keys will then be reset and will react again on contact.

... one or several sensors do not react after the fuse has been discon-

nected and then reconnected.

Possible cause: Faulty sensor key or element.

After disconnecting and reconnecting the fuse twice, disconnect the fuse

again and inform the after-sales service.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kuppersbusch EEB 6850.0 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kuppersbusch EEB 6850.0

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info