Bedienungsanleitung Kuppersbusch IKE 237.5 (Seite 18 von 18) (Deutsch)

514084

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

Important:

Never use sharp metal tools to scrape off frost

from the evaporator as you could damage it.

Do not use a maechanical device or any artificial

means to speed up the thawing process other

than those recommended by the manufacturer.

A temperature rise of the frozen food packs,

during defrosting, may shorten their safe

storage life.

Interior light

The light bulb inside the refrigerator compartment

can be reached as follows:

- unscrew the light cover securing screw.

- unhook the moving part as shown in the figure.

If the light does not come on when the

door is open, check that it is screwed into place

properly. If it still does not light up, change the

bulb. The rating is shown on the light bulb cover.

D411

Defrosting

Frost is automatically eliminated from the evaporator

of the refrigerator compartment every time the motor

compressor stops, during normal use. The defrost

water drains out through a trough into a special

container at the back of the appliance, over the

motor compressor, where it evaporates.

It is important to periodically clean the defrost

water drain hole in the middle of the refrigerator

compartment channel to prevent the water

overflowing and dripping onto the food inside.

Use the special cleaner provided, which you will

find already inserted into the drain hole.

The freezer compartment, however, will become

progressively covered with frost. This should be

removed with a plastic scraper , whenever the

thickness of the frost exceeds 4 mm. During this

operation it is not necessary to switch off the power

supply or to remove the foodstuffs.

However, when the ice becomes very thick on the

inner liner, complete defrosting should be carried out

and it is advisable to carry out this operation when

the appliance is empty.

To carry out complete defrosting of the freezer

compartment proceed as follows:

1. pull out the plug from the wall socket or turn the

thermostat knob to the «O» setting;

2. remove any stored food, wrap it in several layers

of newspaper and put it in a cool place;

3. leave the door open, place a basin on the top

shelf of the refrigerator compartment under the

drain hole, remove the plugas shown in the

figure;

4. when defrosting is completed, dry the interior

thoroughly and refit the plug;

5. turn the thermostat knob back to the required

setting or replace the plug in the power socket.

After letting the appliance run for at least half an

hour, replace the previously removed food into

the compartment.

PR151

D037

The Manufacturer declines all responsibility if

the above safety precautions are not observed.

This appliance complies with the following

E.E.C. Directives:

- 87/308 EEC of 2/6/87 relative to radio interference

suppression.

- 73/23 EEC of 19.2.73 (Low Voltage Directive) and

subsequent modifications;

- 89/336 EEC of 3.5.89 (Electromagnetic

Compatibility Directive) and subsequent

modifications.

CUSTOMER SERVICE AND SPARE PARTS

If the appliance is not functioning properly, check

that:

• the plug is firmly in the wall socket and the mains

power switch is on;

• there is an electricity supply (find out by plugging

in another appliance);

• the thermostat knob is in the correct position.

• If there are water drops on the bottom of the

cabinet, check that the defrost water drain

opening is not obstructed (see “Defrosting”

section).

• If your appliance is still not working properly after

making the above checks, contact the nearest

service centre.

To obtain fast service, it is essential that when you

apply for it you specify the model and serial number

of your appliance which can be found on the

guarantee certificate or on the rating plate located

inside the appliance, on the bottom left-hand side.

INSTALLATION

Location

The appliance should be installed well away from

sources of heat such as radiators, boilers, direct

sunlight etc.

Electrical connection

Before plugging in, ensure that the voltage and

frequency shown on the serial number plate

correspond to your domestic power supply. Voltage

can vary by ±6% of the rated voltage.

For operation with different voltages, a suitably sized

auto-transformer must be used.

The appliance must be earthed.

The power supply cable plug is provided with a

contact for this purpose.

If the domestic power supply socket is not earthed,

connect the appliance to a separate earth in

compliance with current regulations, consulting a

specialist technician.

ATTENTION!

It must be possible to disconnect the appliance from

the mains power supply; the plug must therefore be

easily accessible after installation.

Door reversibility

The appliance’s door has been locked in position for

transport by means of pins on both sides.According

to the door opening direction, remove relevant pins

at the top and at the bottom.

Instructions for totally built-in appliances

50 mm

min.

200 cm

min.

D567

Building-in instructions

Dimensions of housing

Model IKE 187-6 IKE 237-5

Height 1030 mm 1225 mm

Depth 550 mm 550 mm

Width 560 mm 560 mm

For safety reasons, minimum ventilation must be as

shown in Fig.

Attention: keep ventilation openings clear of

obstruction.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kuppersbusch IKE 237.5 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kuppersbusch IKE 237.5

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info