Bedienungsanleitung Kuppersbusch IKE 247.6 (Seite 13 von 14) (Deutsch)

514092

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

Temperature regulation

The temperature is automatically regulated and can

be increased to achieve a higher temperature

(warmer) by rotating the thermostat knob toward

lower settings or reduced (colder) rotating the knob

towards higher settings.

However, the exact setting should be chosen

keeping in mind that the temperature inside the

refrigerator depends on:

• room temperature;

• how often the door is opened;

• the quantity of food stored;

• location of appliance.

A medium setting is generally the most suitable.

Important

If the ambient temperature is high or the

appliance is fully loaded, and the appliance is

set to the lowest temperatures, it may run

continuously causing frost to form on the rear

wall. In this case the dial must be set to a higher

temperature to allow automatic defrosting and

therefore reduced energy consumption.

Fresh food refrigeration

To obtain the best performance:

• do not store warm food or evaporating liquids in

the refrigerator;

• do cover or wrap the food, particularly if it has a

strong flavour.

• Position food so that air can circulate freely round it.

Movable shelves

The walls of the refrigerator are equipped with a

series of runners so that the shelves can be

positioned as desired.

D338

Positioning the door shelves

To permit storage of food packages of various sizes,

the door shelves can be placed at different heights.

To make these adjustments proceed as follows:

Gradually pull the shelf in the direction of the arrows

until it comes free, then reposition as required.

Humidity control

The glass shelf incorporates a device with slits

(adjustable by means of a sliding lever), which

makes it possible to regulate the temperature in the

vegetable drawer(s).

Close the slots to obtain a warmer temperature and

greater humidity.

Open the slots to obtain a cooler temperature and

less humidity.

PR271

PRXXX

Open the door and push the appliance against the

side of the kitchen unit opposite to that of appliance

hinges.

Fasten the appliance with 4 screws provided in the

kit included with the appliance. Snap vent grille (C)

and hinge cover (D) into position.

D724

Apply the sealing strip pushing it between the

refrigerator and the adjacent cabinet.

It is necessary that the niche is provided with a

conduct of ventilation having the following

dimensions:

Depth 50 mm

Width 540 mm

Slide the appliance into the recess, pushing it

against the wall on the handle side.

D022

PR01

540

D727

50 mm

min.

200 cm

min.

D567

Building-in instructions

Dimensions of housing

Model IKE 197-6 IKE 247-6

Height 1030 mm 1225 mm

Depth 550 mm 550 mm

Width 560 mm 560 mm

For safety reasons, minimum ventilation must be as

shown in Fig.

Attention: keep ventilation openings clear of

obstruction.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kuppersbusch IKE 247.6 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kuppersbusch IKE 247.6

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info