Bedienungsanleitung Kuvings UL-110M (Seite 9 von 23) (Englisch)

653328

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

HOW TO DISASSEMBLE AND CLEAN

Note |

Place the juicing bowl under running

water and unplug the compression

silicone to clean the pulp spout.

• Soak the juicing bowl in a solution of

warm water with baking soda or little bit

of bleach to clean the excess build up.

Tip |

• It is not necessary to completely

clean the juicer in between making

multiple juices during a single juicing

session.

• When  nished with juicing, always

disassemble and clean thoroughly

between juicing sessions to prevent

residue buildup.

Tip |

Clean the base with a soft damp towel

and dry.

Note |

Remove the juicing screw, strainer and

rotation wiper unit from the juicing bowl.

Clean with provided brush.

Note |

Tip |

Note |

Under running water, clean the outside

of the juicing screw with a dish scrub. Use

the tip of the cleaning brush to push out

any residue in the crevices on the bottom

of the juicing screw.

With the smart cap closed,  ll the

juicing bowl with water and turn on

the juicer.

Let it run for a moment. Open the

smart cap and let the water run out

of the juicing bowl.

• If the towel is dripping wet, make sure

to squeeze out the excess liquid before

using it on the juicer.

• After juicing ingredients with seeds, make

sure to thoroughly clean the bottom

crevice of the juicing screw. If this area

isn’t properly cleaned, it can a ect the

balance between the juicing screw and

the strainer and damage the parts.

• Extract all the remaining pulp in the

juicing bowl before stopping the juicer.

• For easier clean up, operate the juicer for

an additional 30 seconds after the juice is

extracted.

• When the drum lid is stuck, press the

REVERSE – OFF – FORWARD button in

this order, switching back and forth 2 to

3 times to dislodge. Then place hands

on top of the drum lid and firmly press

down simultaneously turning the drum

lid counter clockwise to open.

• Thoroughly clean the juicing screw

ensuring that the juicing screw is clean

without any residue.

• Completely dry before using.

• Immediately clean the juicer after each

use. If remaining residue in the juicer dries

up, it can make disassembling and clean-

up di cult. The excess build up can cause

poor performance in future uses.

• For easier disassembly, place the top-

set in the sink and run the water through

from the top of the top-set.

• Thoroughly dry the bottom of the juicing

screw where it connects to the metal

cylinder shaft on the base.

Switch OFF and unplug the power cord

from the wall outlet.

1 4 6

* The products illustrated/photographed in this booklet may vary slightly from the actual product.

Quick Rinsing

Turn the drum lid counter clockwise to

open.

Turn the top-set counter clockwise and lift

o the base.

When moving the appliance, do not lift by

grabbing the feeding tube. Always lift the

appliance by grabbing the base or handle.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kuvings UL-110M Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info