Bedienungsanleitung Kyocera FS6020 (Seite 72 von 110) (Englisch)

20377

Zoom out

Zoom in

Vorherige Seite

1/110

Nächste Seite

Chapter 2 Paper Selection

2-5

The basic rule for printing on adhesive labels is that the

adhesive must never come into contact with any part of the

printer. Adhesive paper sticking to the drum or rollers will

damage the printer.

Label paper must be manually fed.

Label paper has a structure comprised of three layers, as

shown in the figure below. The top sheet is printed on. The

adhesive layer consists of pressure-sensitive adhesives. The

carrier sheet (also called the linear or backing sheet) holds

the labels until use. Due to the complexity of its composition,

adhesive-backed label paper is particularly likely to give

trouble in printing.

Adhesive label paper must be entirely covered by its top

sheet, with no spaces between the individual labels. Labels

with spaces in between are apt to peel off, causing serious

paper jam problems.

Some label paper is manufactured with an extra margin of

top sheet around the edge. Do not remove the extra top sheet

from the carrier sheet until after printing is finished.

The table below lists the specifications for adhesive label

paper.

Postcards

Fan the stack of postcards and align the edges before loading

them in the MP tray. Make sure the postcards you are going

to set are not curled. Feeding curled postcards may cause

paper jams.

Some postcards have rough edges on the back (those are

created when the paper is cut). In this case, put the postcards

on a flat place and rub the edges with, for example, a ruler to

smooth them.

Envelopes

The printer can print on envelopes using paper with a basis

weight of 70 to 100 g/m

(19 to 27 lb/ream). Envelopes must

be manually fed.

An envelope is a more complex object than a single sheet of

paper. For this reason, it may not be possible to obtain

consistent print quality over the entire envelope surface.

Many envelopes have a diagonal grain orientation (See

Paper

Grain on page 2-3

). This orientation is more likely to wrinkle

and crease on its way through the printer. Before purchasing

envelopes for use with the printer, test a sample to verify the

envelope’s suitability.

Do not use envelopes that have an encapsulated liquid

adhesive.

Avoid long printing runs consisting of envelopes only.

Extensive envelope printing can cause premature printer

wear.

To avoid jamming due to curled envelopes, do not leave more

than approximately 10 printed envelopes stacked in the paper

trays during multiple envelope printing.

Adhesive-Backed Labels

Item Specification

Weight of top sheet 44 to 74 g/m

(12 to 20 lb/ream)

Composite weight 104 to 151 g/m

(28 to 40 lb/ream)

Thickness of top sheet 0.086 to 0.107 mm (3.9 to 4.2

mils)

Composite thickness 0.115 to 0.145 mm (4.5 to 5.7

mils)

Moisture content 4 to 6 % (composite)

Top sheet (White

bond paper)

Adhesive

Carrier sheet

Acceptable

Unacceptable

Top

sheet

Carrier

sheet

NOTE

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kyocera FS6020 Seite 72

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info