20433
33
Zoom out
Zoom in
Vorherige Seite
1/143
Nächste Seite
Chapter 3 Using the Operator Panel
3-17
When the desired maximum number of jobs is set,
press the ENTER key.
Press the
MENU
key. The display returns to Ready.
Q
QQ
Q Maximum Space Assigned to Temporary Code Jobs
This changes the hard disk space that holds temporary code
jobs. You can change the maximum space from 0 to 9999
(megabytes). The actual maximum size depends on the size of
free hard disk space, however. The default size is 1/6 of the to-
tal hard disk space, rounded off in units of 50 MB. For example,
if the total hard disk space is 3.2 GB, the default size is 500 MB.
Press the
MENU
key.
Press the 3 or 4 key repeatedly until e-MPS > ap-
pears.
Press the 2 key.
Press the 3 or 4 key repeatedly until >e-MPS Con-
figuration > appears.
Press the 2 key.
Press the 3 or 4 key repeatedly until >>Temp. Code
JOB Size appears.
To change the maximum disk space, press the ENTER
key. A blinking cursor (_) appears.
Press the 3 or 4 key to increase or decrease, respec-
tively, the value at the blinking cursor. Use the 2 and
1 keys to move the cursor right and left.
When the desired size is displayed, press the ENTER
key.
Press the MENU key. The display returns to Ready.
Q
QQ
Q Maximum Space Assigned to Permanent Code Jobs
This changes the hard disk space that holds permanent code
jobs. You can change the maximum space from 0 to 9999
(megabytes). The actual maximum size depends on the size of
free hard disk space, however. The default size is 1/6 of the to-
tal hard disk space, rounded off in units of 50 MB. For example,
if the total hard disk space is 3.2 GB, the default size is 500 MB.
Press the MENU key.
Press the 3 or 4 key and select e-MPS >.
Press the 2 key.
Press the 3 or 4 key repeatedly until >e-MPS Con-
figuration > appears.
Press the 2 key.
Press the 3 or 4 key and select >>Perm. Code JOB
Size.
Press the
ENTER
key, the message display shows a
blinking cursor (_).
Press the 3 or 4 key to increase or decrease, respec-
tively, the value at the blinking cursor. Use the 2 and 1
keys to move the cursor right and left.
When the desired size is displayed, press the ENTER
key.
Press the MENU key and the message display returns
to Ready.
e-MPS >
>e-MPS >
Configuration
>>Temp. Code JOB
Size 0500MB
>>Temp. Code JOB
Size 050
0MB
9
10
1
2
3
4
5
6
7
8
9
10
e-MPS >
>e-MPS >
Configuration
>>Perm. Code JOB
Size 0500MB
>>Perm. Code JOB
Size 050
0MB
1
2
3
4
5
6
7
8
9
10
33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Kyocera FS9500DN wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info