Bedienungsanleitung Kyocera km 1500 laser 15ppm (Seite 48 von 76) (Englisch)

435980

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

Section 6 COPY DEFAULT SETTINGS

6-2

F14 Multi-Bypass Tray Paper

Size

Registers the size of paper that is to be set on

the multi-bypass tray.

* The “XXX” shown here refers to the actual

width of the paper as registered under the

“Non-Standard Size Paper Width” and it

is that number which will be shown on the

display.

-A4: A4

-A5: A5

-A6: A6

-Fo: Folio

-Lg: Legal

-St: Statement

-Lt: Letter

-o2: Oficio II

XXX: Non-Standard Size

(Inch specification default:

Letter)

(Metric specification

default: A4)

6-4

6-7

F15 Non-Standard Size Paper

Width

Sets the width of the paper to be set on the

multi-bypass tray when that paper is of a

non-standard size.

* Non-standard size paper of up to 14", or

356 mm, in length can be used.

Inch specification:

4.13 – 8.50 (Default: 4.13)

Metric specification:

105 – 216 mm

(Default: 105 mm)

6-4

6-5

F21 Off Mode ON/OFF Sets whether the Off mode, which

automatically turns most of the power to the

copier off when a certain time elapses without

any operation being performed, will engage

automatically or not.

* If the Off mode interferes in any way with

your copying operations, turn this function

OFF. It is recommended, however, that you

try to set a longer time interval until the Off

mode engages before you actually turn it

OFF.

ON*

OFF

6-4

6-5

F23 Low Power Mode Time Sets the amount of time after each copy job is

finished until the Low Power mode

automatically engages.

1/5/15/30/45/60/90/120/

180/240 (minutes)

(Default: 15 minutes)

6-4

6-7

F24 Off Mode Time Sets the amount of time without any operation

being performed until the Off mode

automatically engages. It is also possible to

disable the Off mode. When the Off mode is

turned OFF, this default setting will not

appear. (See “Off Mode ON/OFF”)

* If the Off mode is turned off under the “Off

Mode ON/OFF” setting, this default setting

will not appear.

* It is recommended that you try to set a

longer time interval before the Off mode

engages if you use the copier frequently, and

to a shorter time if it is used less frequently.

* In order to disable the Off mode, see “Off

Mode ON/OFF”.

15/30/45/60/90/120/180/

240 (minutes)

(Default: 30 minutes)

6-4

6-7

F25 Alarm ON/OFF Sets whether the alarm which sounds when an

error occurs, etc., will be turned ON or OFF.

OFF*

6-4

6-5

F26 Document Processor

Leading Edge Timing

Adjustment

Adjusts the location of the copied image if it is

shifted off-center (either forward or backward)

when the Document Processor is used to make

copies.

* If the optional Document Processor is not

installed on your copier, this default setting

will not appear.

-32 – 32 (1-step

increments)

(Each one-step adjustment

is equal to a 0.3 mm shift.)

(Adjustment is complete

at the time of purchase.)

6-4

6-9

F27 Upper Drawer Skewed

Feed Adjustment

Adjusts for off-center printing. -1.0 – 3.0 (mm)

(Adjustment is complete

at the time of purchase.)

6-4

6-6

Item

number

Default Description Available settings

Reference

page

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kyocera km 1500 laser 15ppm Seite 48

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info