Bedienungsanleitung Kyocera km 1810p (Seite 40 von 65) (Englisch)

435763

Zoom out

Zoom in

Vorherige Seite

1/65

Nächste Seite

3-7

3. Printer Driver for Windows 95/98

3-7 Device Options Tab (KPDL2 Driver)

■ Available printer memory (in KB)

Indicates the amount of memory available for printing. As this is determined according to the amount of memory entered as the “VM

Option” setting under “Installable Options”, there is normally no need to change it.

■ Print features

It is possible to change the settings related to various printer functions. Select the desired function here and then change the setting in the

field under “Change setting for: xxxx”. Functions available for selection are as follows:

● EcoPrint

Saves on toner. The factory default setting is “Off”.

● Edge Smoothing

Turning this setting “On” allows the jaggies that appear around the edge of text and graphics to be evened out through the smoothing

process.

● Page Policy

Perform this setting in conjunction with the settings to be made under “Paper source” on page 3-5.

[Auto Size Select] ......................Select this setting when you want to select “AutoSelect Tray” under “Paper source”.

[Cassette Base] .........................Select this setting when you want to select the source of paper feed according to the tray under

“Paper source”.

* If you are going to select “AutoSelect Tray” under “Paper source”, be sure to select “Auto Size Select” here or there is a possibility that

printing will be accomplished onto paper that is difference the expected.

● Job Spooling

When you want to print out more than one set of the same documents, it is possible to have them sorted and ejected one set at a time.

[None] .........................................Does not sort.

[Temporary] ...............................Sorts and prints in order of sets: Set 1, Set 2, Set 3, etc.

* It is necessary to create a RAM disk. (Refer to “● Optional Disk” below.)

■ Installable options

Perform the settings here whenever you add optional equipment. The functions of the optional equipment will only be available to the

printer after you have completed the setting here. Select the desired optional equipment here and then change the setting in the field

under “Change setting for: xxxx”. The optional equipment available for selection are as follows:

● Optional Feeder

Perform this setting according to the installed Option Cassette.

● Optional Disk

Perform this setting when you want to create a RAM disk. Refer to “Chapter 1, 2-2 RAM Disk” on page 2-1 for more detailed information

on creating a RAM disk.

* In order to create a RAM disk, it is necessary to increase the memory capacity of your printer. After increasing memory, perform the

setting here according to the “VM Option” setting below.

● VM Option

Perform this setting according to the amount of memory in your printer. If a mistake is made in this setting, there is a possibility that

printing will not be accomplished properly.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kyocera km 1810p Seite 40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info