Bedienungsanleitung Kyocera KM2020 (Seite 95 von 124) (Englisch)

17456

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

8-1

Section 8 TROUBLESHOOTING

Carry out the corresponding corrective procedure when any of the error messages shown in the table below are

displayed.

If one of the following indications is Displayed

Display Corrective Procedure

Reference

Page

“E12” appears on the copy quantity display.

No 11" × 8

1/2

"/A4 size paper was available in either the drawer or the Paper

Feeder (multi-bypass tray) at the time when the report was attempted to be

output. Press the [Paper Select] key and select the supply drawer, then press

the [Start] key. Paper will be supplied from the drawer selected.

–

“E14” appears on the copy quantity display. An original size that cannot be copied has been set. Check the original.

• The original was set in a vertical direction during the Book Border

Erasure copying operation. Set the original horizontally.

• An irregular size original was set during the Border Erase or Merge

Copy operation.

• An original size other than 8

1/2" × 11", 11" × 17", A3, A4R, A5R, B4 or

B5R was set to make a split copy or a 2-Sided Copy from a double-page

spread original.

5-8

5-8, 5-10

5-4

“E15” appears on the copy quantity display. A size that cannot be copied on both sides has been specified. 2-Sided copies

cannot be taken when A6R, B6R, Postcard, Irregular Size or the paper size

has not been specified. Specify a paper size that can be used.

5-1

The Toner Waste display blinks on and “E31”

appears on the copy quantity display.

The waste toner box is full. Replace it with a new waste toner box. 9-4

“E32” appears on the copy quantity display. The Toner Container has not been set. Set the Toner Container. 9-4

The Replenish Toner display blinks on and off. There is very little toner remaining. Copying can be continued for a short

while before running out of toner. Replace the toner container with a new

one as soon as possible.

9-4

The Replenish Toner display blinks on and

“E33” appears on the copy quantity display.

Copies cannot be produced because there is no toner. Replace the toner

container with a new one.

9-4

“E70” appears on the copy quantity display. If the optional Document Processor is being used, there are originals left on

the original table. Remove the originals, return them to the original table

and try copying them again.

–

“E71” appears on the copy quantity display. The copier will try to make copies of the originals it could not copy before.

Return all of the originals to the original table and try copying them again.

–

“E72” appears on the copy quantity display. Originals were set in the optional Document Processor when copying on

2-sides (front and back sides), when copying from the platen in 2-Sided

copy, 2 in 1, 4 in 1 or when sorting copies. Remove the originals from the

Document Processor, replace the originals on the Original Table after

exiting the front and back copying, 2-Sided copy, 2 in 1, 4 in 1 or Sort Mode

and resume copying.

–

“E90” appears on the copy quantity display. Memory is full.

Press the [Enter] key to start outputting the copies read in. Press the

[Reset] key or the [Stop/Clear] Key to delete the data read in. Reduce the

number of originals and repeat the copying procedure.

–

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kyocera KM2020 Seite 95

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info