Bedienungsanleitung Kyocera KM6230 (Seite 24 von 167) (Englisch)

17490

Zoom out

Zoom in

Vorherige Seite

1/167

Nächste Seite

Section 3 PREPARATIONS

2A080030A

KM-6230 (KME)

/ 131

3-4

2. Setting originals

1 What is the DF for?

The DF (Document Feeder) automatically feeds and scans each original, one by one, for

copying. When you make copies from two-sided originals, it will automatically turn the

originals over in order to copy the reverse side as well.

2 Originals that can be set in the DF…

• Sheet originals

• Thickness:

One-sided originals: between 35 g/m

- 160 g/m

Two-sided originals: between 50 g/m

- 120 g/m

• Size: Max. 11" x 17" (A3) - Min. 5-1/2" x 8-1/2" (A5R)

• Number of sheets:

100 sheets (11" x 8-1/2" [A4] or smaller [75 g/m

or 80 g/m

])

70 sheets (8-1/2" x 14" [B4] or larger [75 g/m

or 80 g/m

])

(However, 30 sheets maximum when using the auto selection mode)

3 Cautions when using the DF

DO NOT set originals of the follow types in the DF. In addition, when using perforated

sheets or originals with punch holes, DO NOT insert the end with the perforations or

holes first.

• Transparencies

• Carbon paper, crumpled originals or originals with strong folds, and soft originals such

as vinyl

• Originals which are not rectangular, wet originals, and originals with adhesive tape or

glue

• Originals with clips or staples (In order to use such originals, remove the clips or staples

and straighten any crumples or folds before using them.)

• Clippings or originals with very slippery surfaces

• Originals with wet correction fluid

• Originals with folds (If you must use such originals, smooth out the folded portions

before setting them in the DF.)

4 Setting originals in the DF

1. Adjust the original insert guides to fit the size of the originals.

* Before setting any new originals, remove any originals that are remaining on the

original ejection table. If ejected originals are left on the original ejection table, they

may cause other originals to misfeed.

2. Arrange the originals in order and set them face up (first page face up for two-sided

originals) onto the original table. The original set indicator will light green. If the indica-

tor does not light, reset the originals in the DF.

IMPORTANT!

DO NOT set more originals than indicated on the sticker that is attached to the rear

original insert guide. If more than the acceptable number of originals is set, the originals

may not feed properly.

* When setting large size originals such as 8-1/2" x 14" and 11" x 17" (B4, Folio, A3),

open the original ejection guide to prevent the ejected originals from sliding off the

original ejection table.

IMPORTANT!

When copying from two-sided originals, each original will be ejected temporarily out of

the original reversing cover before being turned over. DO NOT touch or attempt to re-

move any original at this time as it will cause a misfeed error.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kyocera KM6230 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info