Bedienungsanleitung La Crosse WS-1516-IT (Seite 3 von 20) (Englisch)

626738

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

4. Afterwards, the Weather Center will start receiving data from the transmitter. The

transmission reception icon will be blinking to indicate that the station is trying to get the

thermo-hygro transmitter data. The outdoor temperature, humidity, wind data should then

be displayed on the Weather Center. If this does not happen after 135 seconds, the

batteries will need to be removed from all units. You will have to start again from step 2.

5. The transmitter reception icon is now blinking again to indicate that the station is trying to

get the rain sensor data. It will stop blinking once the rain sensor has been detected. If this

does not happen after 135 seconds, you will need to start again from step 2.

6. You may need to check the cable for correct connection and all the components for correct

function by manually turning the wind-gauge by moving the wind-vane; tilting the rain

sensor to hear the impact of the internal moving seesaw, etc. (see Positioning below).

7. Time and date shall be manually set (See Manual Setting below).

8. After the Weather Center has been checked for correct function with regard to the above

points and found fit, the initial set up of the weather station system is finished and the

mounting of the system components can take place. It must be ensured however that all

components work properly together at their chosen mounting or standing locations. If e.g.

there appear to be problems with the 915 MHz radio transmission, they can be overcome

by slightly changing the mounting locations or turning the base station.

Note:

The radio communication between the receiver and the transmitters in the open field reaches

distances of max 330 feet, provided there are no interfering obstacles such as buildings, trees,

vehicles, high voltage lines, etc.

9. Radio interferences created by PC screens, radios or TV sets can in some cases entirely

cut off radio communication. Please consider this when choosing standing or mounting

locations.

Note :

 After batteries are installed in the transmitter, install the batteries in the weather center to

receive the signal from the transmitters as soon as possible. If the weather center is

powered more than 5 hours after the transmitter is powered, the weather center will never

receive signal successfully from the transmitters. In this case, user will need to reinstall the

batteries from all the transmitters to redo set-up procedure.

 After batteries are installed, there will be synchronization between weather center and the

transmitters. At this time, the signal reception icon will be blinking. When the signal is

successfully received by the weather center, the icon will be switched on. (If it is not

successful, the icon will not be shown in LCD) So the user can easily see whether the last

reception was successful (icon on) or not (icon off). On the other hand, the short blinking of

the icon shows that a reception is in progress.

 If the signal reception is not successful on the first frequency (915MHz) for 45 seconds, the

frequency is changed to 920MHz and the learning is tried another 45 seconds. If still not

successful, the reception is tried for 45 seconds on 910MHz. This will also be done for re-

synchronization.

Transmitter signal

reception icon

HOW TO INSTALL AND REPLACE THE BATTERIES INTO THE THERMO-

HYGRO SENSOR

The outdoor Thermo-hygro sensor works with 2 x AA, IEC LR6 1.5V

Alkaline batteries. To install and replace the batteries, please follow the

steps below:

1. Uninstall the rain cover of the transmitter.

2. Remove the battery compartment cover.

3. Insert the batteries, observing the correct polarity (see the marking

in the battery compartment).

4. Replace the battery cover.

Note:

In the event of changing batteries in any of the units, all units need to be reset by following the

setting up procedures. This is because a random security code is assigned by the thermo-hygro

sensor at start-up and this code must be received and stored by the Weather Center in the first

several minutes of power being supplied to it.

HOW TO INSTALL AND REPLACE THE BATTERIES INTO THE RAIN SENSOR

The rain sensor works with 2 x AAA, IEC LR3, 1.5V Alkaline batteries. To install and replace the

batteries, please follow the steps below:

1. Press tabs back to unlock rain sensor cover. (Figure 1)

2. Lift rain sensor cover to access battery compartment. (Figure 2)

3. Insert the batteries, observing the correct polarity (see the marking in the battery

compartment). (Figure 3)

4. Replace the battery cover and the rain cover onto the unit.

Note:

In the event of changing batteries in any of the units, all units need to be reset by following the

setting up procedures. This is because a random security code is assigned by the rain sensor at

start-up and this code must be received and stored by the Weather Center in the first several

minutes of power being supplied to it.

Figure 1

Figure 2

Figure 3

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

La Crosse WS-1516-IT Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info