Bedienungsanleitung La Crosse WS-7015 (Seite 4 von 12) (Englisch)

626737

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

South

North

Solar Cell

Magnet

Mast

Mounting example of

Remote Wind Sensor to

a Mast

This addressing is only necessary if – within the sensor’s transmission range (up to 330 ft

(100 m)) – two Base Stations with respectively assigned Indoor Sensors need to be

operated (Base Station 1 showing the data of Indoor Sensor 1, Base Station 2 showing

the data of Indoor Sensor 2).

The Rain Volume Sensor as well as the Wind Sensor also have fixed addressing and

belong to this group since their measured values too have their fixed location in the

display.

The second group of sensors are the optionally obtainable types WS 7015-22, WS 7015-

27, WS 7015-28 as well as the Remote Outdoor Sensor (included with basic shipment).

These sensors transmit their data signal to be displayed in the outdoor section in the

upper right part of the LCD. It is possible to operate up to 8 sensors which can be

selected through the sensor selection in the display. It is thus necessary to assign a

respective address to each sensor determining their fixed location in the upper right

display section. Therefore please observe for these three types in the notes on

addressing.

Remote Indoor Sensor

The Remote Indoor Sensor included with the basic shipment requires two Type Mignon

AA, IEC LR6, 1.5V batteries for operation. It contains one respective sensor for

temperature, humidity and air pressure. The data of the Remote Indoor Sensor generally

appear in the indoor display section in the upper left part of the LCD. Besides indoor

temperature and indoor humidity it measures the air pressure prerequisite for the display

of air pressure, air pressure tendency, weather tendency and air pressure history.

Remote Wind Sensor

The Remote Wind Sensor simultaneously acquires wind direction and wind strength at its

mounting location. It is operated by a solar cell with a battery backup during darkness and

provides addressing which cannot be altered by the user.

Remote Rain Volume Sensor

The Remote Rain Volume Sensor also works with solar power supply and provides

addressing not alterable by the user. The funnel has a 5.12 in (130 mm) diameter, which

represents an area of 20.45 in

, the calculation base for the rain volume.The amount of

water flowing through the funnel initiates a number of pulses. These pulses are converted

to in or mm in the Base Station and then displayed.

Remote Outdoor Sensor

The Remote Outdoor Sensor included with the basic shipment allows the transmission of

the temperature and humidity values at its mounting location.

This sensor can be addressed freely for display within the outdoor display section in the

upper right part of the LCD (see Display Overview). By default all Remote Outdoor

Sensors are set to Sensor 1. Individual addressing is however possible.

7. Mounting

Base Station

The Base Station can be placed on any smooth surface (e.g. table, bookshelf, etc.) by

pulling out the foldable stand or wall mounted at any desired location by means of a

hanging hole at the back of the device.

Important Note!

It is recommended to check that the 433MHz signals are properly received before

permanently mounting the Professional Weather Station (drilling of holes, etc.).

Should the Weather Station not pick up signal from the desired location a slight

relocation will help in most any case. Once the signals are received, the system can

be mounted permanently.

Mounting is but a preparation for the setup. Just before the final setup of the Base

Station the magnets have to be placed into the sensors.

Recommendation!

In order to test all sensor functions at first setup the sensors can prior to mounting

be placed on a smooth surface (table, etc.) and put into operation (see Item 8

Setting Up).

Remote Wind Sensor

Mounting takes place either to a mast or at the upper rim of a wall. It is important to mount

the device in such a way that the solar cell in the sensor housing is pointing in a southerly

direction. It is further important to mount the device in a zone not prone to wind shadow,

i.e. the wind must be allowed to travel freely about the sensor from all directions.

Remove the transport protection from the sensor head and make sure that weather-vane

and wind wheel can move freely and easily. Put sensor head, holding tube and mast/wall

holder together and fix the components by use of the supplied screws. For basic

mounting the Wind Sensor must be pointing exactly in a southerly direction (solar cell to

the south) in order to provide an exact northerly reference point for the evaluation

electronics.

Note!

An exact southerly alignment of the sensor respectively its solar cell is very

important since this alignment will provide the reference point for the Wind

Direction Sensor.

In order to obtain correct measuring values exact perpendicular mounting of the

sensor to the mast must be observed. Axial stress to weather-vane and wind wheel

should be avoided.

Remote Indoor Sensor

Mount the sensor to its desired location. Keep in mind that the sensor is not designed to

operate outdoors or in rooms prone to excessive humidity. Data of the Indoor Sensor are

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

La Crosse WS-7015 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info