Bedienungsanleitung La Nordica Isetta Evo 4.0 (Seite 27 von 92) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

696185

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

ENGLISH

LIGHTING

WARNING: After the rst ignition you can smell bad odours (owing to the drying of the glue used in the garnitures or of the paint)

which disappear after a brief using of the appliance. It must be ensured, in any case, a good ventilation of the environment.

Upon the rst ignition we suggest loading a reduced quantity of fuel and slightly increasing the caloric value of the equipment.

It is FORBIDDEN to use any liquid substance as for ex. alcohol, gasoline, oil and similar.

Never switch on the device when there are combustible gases in the room.

To perform a correct rst lighting of the products treated with paints for high temperature, it is necessary to know the following information:

• the construction materials of the involved products are not homogeneous, in fact there are simultaneously parts in cast iron, steel,

refractory material and majolica;

• the temperature to which the body of the product is subject is not homogeneous: from area to area, variable temperatures within the

range of 300°C - 500°C are detected;

• during its life, the product is subject to alternated lighting and extinguishing cycles in the same day, as well as to cycles of intense use

or of absolute standstill when season changes;

• the new appliance, before being considered seasoned has to be subject to many start cycles to allow all materials and paints to

complete the various elastic stresses;

• in detail, initially it is possible to remark the emission of smells typical of metals subject to great thermal stress, as well as of wet paint.

This paint, although during the manufacture it is backed at 250 °C for some hours, must exceed many times and for a given period of

time the temperature of 350 °C before becoming completely embedded in the metallic surfaces.

Therefore, it is extremely relevant to take these easy steps during the lighting:

1. Make sure that a strong air change is assured in the room where the appliance is installed.

2. During the rst starts, do not load excessively the combustion chamber (about half the quantity indicated in the instructions manual)

and keep the product continuously ON for at least 6-10 hours with the registers less open than the value indicated in the instructions

manual.

3. Repeat this operation for at least 4-5 or more times, according to your possibilities.

4. Then load more and more fuel (following in any case the provisions contained in the installation booklet concerning maximum load)

and, if possible, keep the lighting periods long avoiding, at least in this initial phase, short ON/OFF cycles.

5. During the rst starts, no object should be leaned on the appliance and in detail on enameled surfaces. Enameled surfaces

must not be touched during heating.

6. Once the «break-in» has been completed, it is possible to use the product as the motor of a car, avoiding abrupt heating with excessive

loads.

To light the re, it is suggested to use small wood pieces together with paper or other traded lighting means.

The openings for air (primary and secondary) must be opened together (you must open the eventual Ignition control, and buttery valve

placed on the pipe of smokes exhaust). When the wood starts burning, you may load other fuels and adjust the air for combustion according

to the instructions on paragraph TECHNICAL DESCRIPTION.

Please always be present during this phase.

Never overload the appliance (see cap. TECHNICAL DESCRIPTION / hourly consumption). Too much fuel and too much air for

combustion can cause overheating and therefore damage the appliance. The warranty does not cover the damages due to

overheating of the equipment.

LOW EMISSION FIRE LIGHTING

Smokeless combustion is a way of lighting a re able to signicantly reduce the emission of harmful substances. The wood burns gradually

from the top downwards, so combustion is slower and more controlled. Burnt gases pass through the high temperatures of the ame and

therefore burn almost completely.

Place the logs in the hearth a certain distance apart as shown in the Picture 7. Arrange the largest at the bottom and the smallest at the top,

or vertically in the case of tall narrow combustion chambers. Place the re starter module on top of the pile, arranging the rst logs in the

module at right angles to the pile of wood.

Fire STARTER MODULE. This re starter module replaces a paper or cardboard starter.

Prepare four logs, 20 cm long with a cross section of 3 cm by 3 cm Picture 7. Cross the four logs and place them on top of the pile of wood

at right angles, with the re lighter (wax impregnated wood bre for example) in the middle. The re can be lit with a match. If you want, you

can use thinner pieces of wood. In this case, you will need a larger quantity.

Keep the ue gas exhaust valve and combustion air regulator open.

After lighting the re, leave the combustion air regulator open in the position shown in according to the instructions on paragraph TECHNICAL

DESCRIPTION

FUEL PRIMARY Air SECONDARY Air TERTIARY air

Wood CLOSED 1/2 OPEN PRE-ADJUSTED

IMPORTANT:

• do not add further wood between one complete load and the next;

• do not suocate the re by closing the air intakes;

• regular cleaning by a chimney sweep reduces ne particle emissions.

• These instructions are backed by ENERGIA Legno SVIZZERA www.energia-legno.ch

La Nordica Isetta Evo 4.0 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von La Nordica Isetta Evo 4.0

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info