Bedienungsanleitung La Nordica Loriet S DSA (Seite 28 von 104) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

696191

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

ENGLISH

ACCESSORIES

POKER GLOVE

LORIET - DSA SERIES SERIES

LORIET S - DSA SERIES SERIES

The heating of the room takes place:

a) by radiation: the heat is radiated into the environment through the panoramic window and the hot external surfaces of the thermo-

product;

b) by conduction: radiators or heat convectors of the centralised system fed by hot water produced by the boiler (See chapter

CALCULATION OF THE THERMAL POWER).

The thermo-product is supplied with registers for primary and secondary air and a thermostat with which the combustion air is regulated.

1A - PRIMARY Air Register / AUTOMATIC Thermostat (Picture 6).

The thermostat has the task of automatically increasing or decreasing combustion.

Dependent on the position chosen, the thermostat will act on the valve which regulates the intake of air into the furnace, placed on the

back of the cooker. Turn it in a clockwise direction from 0 to 5 to make up the re and in an anti-clockwise direction to reduce combustion.

As this is an extremely precise device, it is advisable to turn it carefully and never force the knob.

2A - SECONDARY Air Register (Picture 6).

This register must be open (i.e. turned completely to the right), in particular for the combustion of wood (see paragraph NORMAL

OPERATION). The secondary air, passing between the double glass of the re door, heats up and triggers the dual combustion, keeping the

glass clean at the same time (register open).

To ignite the ame follow the instructions below (see Cap. IGNITION) :

• Open the buttery valve placed on the ue gas exhaust pipe must also be opened.

• Position the thermostat knob on position 5 (maximum opening).

• After having started the re with small pieces of wood and waited until it is well lit, adjust the thermostat to the positions corresponding

to the desired heat (0÷5).

• Close the buttery valve placed on the ue gas exhaust pipe must also be opened.

The register regulation necessary in order to obtain nominal caloric output is the following (see Cap. NORMAL OPERATION):

PRIMARY air SECONDARY air TERTIARY air

LORIET - DSA Pos. 3 Picture 6 Pos. ●●● Picture 6 PRE-ADJUSTED

LORIET S - DSA Pos. 3 Picture 6 Pos. ●● Picture 6 PRE-ADJUSTED

FLUE

Essential requirements for correct appliance operation:

• the internal section must preferably be circular;

• the appliance must be thermally insulated and impermeable and built with suitable materials which are resistant to heat,

combustion products and any condensation;

• there must be no narrowing and vertical passages with deviations must not be greater than 45°;

• if already used, it must be clean;

• all the sections of the ue gas duct must be accessible to inspection;

• inspection openings must be provided for cleaning.

• the technical data from the instruction manual must be respected;

If the ues are of a square or rectangular section, the internal edges must be rounded with a radius of not less than 20 mm.

For the rectangular section, the maximum ratio between the sides must be ≤ 1.5.

A section which is too small causes a reduction in draught. A minimum height of 4 m is advisable.

The following materials are FORBIDDEN and compromise the good operation of the appliance: asbestos cement, galvanised steel, rough and

porous internal surfaces. Picture 1 shows some example solutions.



For a correct installation please respect the sections/lengths of the ue shown in the technical data table. By installations

with dierent dimensions the ue must be suitably sized in accordance with EN13384-1.

The draught created by your ue must be sucient but not excessive.

A section of the ue which is too large can present a volume which is too large to heat and therefore cause operating diculties for the

appliance; to avoid this, it is necessary to intubate the appliance for its entire height. A section which is too small causes a reduction in draught.

ATTENTION: as far as concern the realisation of the ue connection and ammable materials please follow the requirements

provided by UNI 10683 standard. The ue must be at a suitably distance from ammable or combustible material using

suitable insulation or an air space.

It is FORBIDDEN to pass system piping or air ducts inside the ue. It is also forbidden to create moveable or xed openings on

the ue itself, for the connection of further dierent appliances (See chapter CONNECTING A FIREPLACE OR OPEN HEARTH TO THE

FLUE).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

La Nordica Loriet S DSA Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info