Bedienungsanleitung La Nordica LUCY BII (Seite 17 von 72) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

643340

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

FIAMMETTA BII - ASIA BII - GIORGIA BII - FIORELLA BII - LUCY BII

7196601 17

The heating of the environment is made by:

• Convection: (70%) the air passage through the double mantel of the stove releases heat into the environment;

• Irradiation (30%): through the panoramic glass and the external hot surfaces of the stove, the heat is radiated into the environment.

( See chapter CALCULATION OF THE THERMAL POWER).

The stove is equipped with controls of primary and secondary air by which it is adjusted the combustion air.

1A - PRIMARY air register (Picture 6 at page 61)

With the primary air control, which is found below the hearth door it is adjusted the passage of air through the ash drawer and the

grate in the fuel direction. The primary air is necessary for the combustion process. The ash drawer must be regularly emptied, so that

the ash does not obstruct the primary air entry. Through the primary air the re is also kept alive.

During wood combustion, the register of primary air must be opened only for a while, because otherwise the wood burns fast and the

stove may overheat(see chapter NORMAL OPERATION).

2A - SECONDARY air register (Picture 6 at page 61)

On the over part of the door there is the secondary air control. Also this register must be opened (then moved to the right), especially

for wood combustion (see chapter NORMAL OPERATION).

Through this register it is possible to adjust the power of the stove. Leaving it slightly open, according to the ue of the chimney, it is

possible to keep the glass clean.

The adjustment of the registers necessary to reach the rated caloric yield is the following one:

Hourly consumption Kg/h PRIMARY air SECONDARY air TERTIARY AIR

1,7

CLOSED OPEN PRE-ADJUSTED

6. FLUE

Essential requirements for correct appliance operation:

• the internal section must preferably be circular;

• the appliance must be thermally insulated and impermeable and built with suitable materials which are resistant to heat, combustion

products and any condensation;

• there must be no narrowing and vertical passages with deviations must not be greater than 45°;

• if already used, it must be clean;

• the technical data from the instruction manual must be respected;

If the ues are of a square or rectangular section, the internal edges must be rounded with a radius of not less than 20 mm.

For the rectangular section, the maximum ratio between the sides must be ≤ 1.5.

A section which is too small causes a reduction in draught. A minimum height of 4 m is advisable.

The following materials are FORBIDDEN and compromise the good operation of the appliance: asbestos cement, galvanised steel, rough

and porous internal surfaces. Picture 1 at page 58 shows some example solutions.

The minimum section must be 4 dm

(for example 20x20 cm) for appliances whose pipe dimensions are less than 200 mm, or 6.25

(for example 25x25 cm) for appliances with a diameter of more than 200 mm.

The draught created by your ue must be sufcient but not excessive.

A section of the ue which is too large can present a volume which is too large to heat and therefore cause operating difculties for the

appliance; to avoid this, it is necessary to intubate the appliance for its entire height. A section which is too small causes a reduction in

draught.

ATTENTION: as far as concern the realisation of the ue connection and ammable materials please follow the requirements provided by

UNI 10683 standard. The ue must be at a suitably distance from ammable or combustible material using suitable insulation or

an air space.

It is FORBIDDEN to pass system piping or air ducts inside the ue. It is also forbidden to create moveable or xed openings on the ue

itself, for the connection of further different appliances (See chapter CONNECTING A FIREPLACE OR OPEN HEARTH TO THE FLUE).

6.1. CHIMNEY POT

The ue draught depends on the suitability of the chimney pot.

It is therefore essential that, if built in a handcrafted way, the exit section is more than twice the internal section of the ue

(Picture 2 at page 58) .

As it must always go past the ridge of the roof, the chimney pot must ensure exhaust even in the presence of wind (Picture 3 at page 59).

The chimney pot must meet the following requirements:

• Have an internal section equivalent to that of the chimney.

• Have a useful exit section of double the internal section of the ue.

• Be built so as to prevent rain, snow or any foreign body entering the ue.

• Be easy to inspect, for any maintenance and cleaning operations.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

La Nordica LUCY BII Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von La Nordica LUCY BII

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info