Bedienungsanleitung La Nordica Monoblocco Ghisa 750 (Seite 22 von 84) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

696299

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

ENGLISH

DESCRIPTION

The device is made up of metal sheet plates in painted steel, castings of cast iron and refractory materials.

The hearth is coated by cast iron castings or IRONKER, the grate holder and the related extractible grating are both made of cast iron. The

combustion chamber assembly is air-tight by welding and covered with a galvanized sheet metal carter.

The devices are equipped with a hearth with double thickness rear part made up of a drilled extractible plate.

Through these holes, pre-heated air gets into the hearth; in this way, it is possible to achieve a post-combustion with an increase of the yield

and a reduction of emissions of unburnt gases.

The sight door is assembled on extensible ball guides, which assure a robust and silent operation reliable in time.

The door lifting counter-weight is supported by two sturdy chains with related pinions.

The ceramic glass (resistant up to 700 °C) of the door allows a charming view on burning ames and avoids any leak of sparks and smoke.

ACCESSORIES

POKER GLOVE

Ventilation KIT

SERIES SERIES OPTIONAL

Under the hearth grating there is a easily extractable ash drawer, also when the appliance works.

The heating of the room occurs:

a) by convection: the passage of air through the coating and the covering hood releases heat in the room.

b) by radiation: through the sight glass and the steel body, heat is radiated into the room.

The device is equipped with registers of primary and secondary air, with which it is possible to adjust the combustion air.

1A - PRIMARY air register (Picture 8)

With the air register located under the door of the hearth, it is possible to adjust the air ow through the ash drawer and the grating in

direction of the fuel. The primary air is necessary for the combustion process. In order to open the passage of primary air the lever should

be completely pulled. The ash drawer has to be emptied regularly, so that ash cannot hinder the intake of primary air for the combustion.

Primary air is also necessary to keep re live.

During the combustion of wood, the primary air register must be opened only a few, since otherwise the wood burns quickly and the

device can overheat (see chapter NORMAL OPERATION).

2A - SECONDARY air register (Picture 8)

Under the door of the hearth there is a secondary air register.

This register must be opened (and therefore the lever completely pushed), in detail, for the combustion of wood, so that unburnt carbon

can be subject to a post-combustion, increasing the yield and assuring the cleaning of the glass (see chapter NORMAL OPERATION).

The adjustment of the registers necessary to reach the rated caloric yield is the following one:

Hourly consumption (kg/h) PRIMARY air SECONDARY air TERTIARY AIR

3,8 CLOSED OPEN PRE-ADJUSTED

FLUE

Essential requirements for a correct operation of the device:

• the internal section must be preferably circular;

• be thermally insulated and water-proof and produced with materials suitable to resist to heat, combustion products and

possible condensates;

• not be throttled and show a vertical arrangement with deviations not greater than 45°;

• if already used, it must be clean;

• all the sections of the ue gas duct must be accessible to inspection;

• inspection openings must be provided for cleaning.

• observe the technical data of the instructions manual;

Should the ues have a square or rectangular section, internal edges must be rounded with a radius not lower than 20 mm. For the rectangular

section, the maximum ratio between the sides must be = 1.5.

A too small section causes a decrease of the draught. It is suggested a minimum height of 4 m.

The following features are FORBIDDEN and therefore they endanger the good operation of the device: asbestos cement, galvanized steel,

rough and porous internal surfaces. In Picture 3 gives some examples of execution.



For a correct installation please respect the sections/lengths of the ue shown in the technical data table. By installations

with dierent dimensions the ue must be suitably sized in accordance with EN13384-1.

The draught created by the ue must be sucient, but not excessive.

A too big ue section can feature a too big volume to be heated and consequently cause diculties in the operation of the device; to avoid

this, tube the ue along its whole height. A too small section causes a decrease of the draught.

ATTENTION: as far as concern the realisation of the ue connection and ammable materials please follow the requirements

provided by UNI 10683 standard. The ue must be properly spaced from any ammable materials or fuels through a proper

insulation or an air cavity.

It is FORBIDDEN to let plant piping or air feeding channels pass in the same ue. Moreover, it is forbidden to create movable or

xed openings on the same for the connection of further other devices (Picture 4).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

La Nordica Monoblocco Ghisa 750 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info